ITV2-OM00114 Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
Do not place your finger in the clearance between the detent plate and the cylinder tube. Never put your finger between the nonrotating plate and cylinder tube. Your finger may be pinched when the piston rod retracts. If your finger is caught, it could injure your finger because the cylinder outputs a considerable amount of force. 2.
Surge voltage suppressor Grommet L plug connector M plug connector DIN terminal Nil Z None With light/surge voltage suppressor With surge voltage suppressor G: Lead wire length 300 mm L: With lead wire (Length 300 mm) M: With lead wire (Length 300 mm) MN: Without lead wire D: With connector S Not available for GZ, HZ and DOZ LN: Without lead wire LO: Without connector MO: Without connector DO
H D DO 2 01 1 8 1 8 Base mounted 02 1 4 1 4 Caution Refer to front matters 58 and 59 for Safety Instructions and pages 3 to 7 for 3/4/5 Port Solenoid Valve Precautions.
: Without connector Manifold Model Applicable manifold type Accessories Function plate (DXT152-14-1A) Note) VO307(-Q) Common or individual exhaust Mounting screw (NXT013-3) Note) It is not applicable to the continuous duty type.
Do not apply force when transferring, mounting and dropping the regulator with a pressure gauge. This may cause misalignment of the pressure gauge pointer. AP100 Precautions for IR2120, IR3120 (air operated type) only Caution 1.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
Do the drain pulling out regularly.
Do not subject the gauge to impacts, such as dropping, during transportation and mounting. This can cause loss of indication accuracy. 2. Do not use in locations with high temperature and humidity. This can cause malfunction. 3. When screwing the pressure gauge into place, be sure to apply your wrench on the square wrench flats.
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display.
Specifications Air, Nitrogen Fluid 100 to 0kPa (-14.5 to 0psi) Operating pressure 0.5MPa (72.5psi) Withstand pressure 0 to 60C (32 to 140F) (with no freezing) Operating and ambient temperature range 10m Filtration degree Element differential pressure resistance 0.15MPa (21.75psi) Applicable tubing material Nylon, Soft nylon, Polyurethane, Soft polyurethane Symbol Note) Do not use in a line
Do not disassemble the power clamp cylinder. The power clamp cylinder consists of a completely sealed structure in order to protect it from welding spatter. Do not disassemble, except for when replacing any of the replaceable parts, as the performance may deteriorate. 10 Power Clamp Cylinder Variations Web Catalog.
Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. Port Air operated Solenoid 12 (P1) External pilot External pilot 2. Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only.
Caution D: With connector DO: Without connector Y: With connector YO: Without connector When using the surge voltage suppressor type, residual voltage will remain. For details, refer to the Web Catalog (VP300/500 Low wattage specification). * Refer to the Web Catalog (VP300/500 Low wattage specification) for details of the DIN terminal. Assembly Example Products do not come assembled.
A Dec / 2021 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL https://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2021 SMC Corporation All Rights Reserved
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
(displayed alternately) Press S-key. displayed alternately 14 - Press and keys for 3 seconds or more. (press S-key to ) is displayed "Initialize" is executed, after 5 seconds. (Release keys till less than 5 seconds to ) Turning off for 1 second Returns to the state immediately after turning on the power supply.
A model should be selected with a gripping force of 7 to 14 times that of the workpiece mass. If high acceleration, deceleration or impact forces are encountered during motion, a further margin of safety should be considered.
C95 CA1 CS1 Mounting Caution Plug mounting q Do not operate in such a way that a load is applied to the piston rod during its retraction. The spring that is built into the cylinder provides only enough force to retract the piston rod. Thus, if a load is applied, the piston rod will not be able to retract to the end of the stroke. Component Parts (Disassembly is not possible.)