SMC Pneumatic Clean Series Note 1) Sampling air flow rate: Number of particles contained in 75l of air Note 2) Actuator: 1 million cycles Solenoid valve: 2 million cycles Particle generation characteristics of CM2 Particle generation characteristics of CXSL Particle generation characteristics of CY1B 106 106 106 Particle concentration (particles/m3) Particle concentration (particles/m3) Particle concentration (particles
Hexagon socket head cap screw (M3 x 0.5 x 16l) 2 pcs.
Mounting by bracket Fix the bracket to the product with the set screws M3 x 5 L (2 pcs.) as attached. The tightening torque of the set screws must be 0.5 to 0.7 Nm. Mounting by panel mount adapter Fix the panel mount adapter to the product with the set screws M3 x 8 L (2 pcs.) as attached.
Display digits Upper digits Middle digits Lower digits Display unit Maximum flow display value L display [ U_1] 9 L 9 m3 x 103 999 m3 999 L (9 L) (999 L) ft display [ U_2] 9.9 ft3 999 ft3 x 106 999 ft3 x 103 999.9 ft3 (999. ft3) (999. ft3) : Operate only the product with unit selection function. button press.
Table 4 BoltTightening torque Size Bolt Recommended tightening torque 10 M3 0.63 Nm 15 20 M4 1.50 Nm 30 M5 3.00 Nm 40 Fig.8 Mounting 2 Using a plate with tapped holes (Refer to Fig. 9). L dimension when the unit is used as a flange is shown in the table below.
Mounting with bracket Fix the bracket to the product with the set screws M3 x 5 L (2 pcs.) or M4 x 5 L (2 pcs.) supplied. The required tightening torque is 0.5 to 0.7 Nm for the M3 set screws and 1.4 to 1.6 Nm for the M4 set screws.
torque Nm (mm) MHF28D M3 x 0.5 0.63 4 MHF2-12D M4 x 0.7 1.5 5 MHF2-16D M5 x 0.8 3 5.5 MHF2-20D M6 x 1 5.2 6 Screw-in depth Model Bolt Max. tightening torque Nm (mm) MHF28D M2.5 x 0.45 0.36 4 MHF2-12D M3 x 0.5 0.63 5.2 MHF2-16D M4 x 0.7 1.5 MHF2-20D M5 x 0.8 3 When MHF2-8D* and MHF2-12D* are mounted body through-hole, use the attached special bolts.
BH BI (UU) 2-M3 x 0.5 (opposite side, same location) (For front port, use hexagon socket head set screw) Q H 2-J through JA depth of counter bore JB (opposite side, same location) 1.5 S BE CA CB BF DD D BD BG A 2.2 (0.4) Note 1) SD 16 BA 2-M3 x 0.5 depth 4 BB W 2-M3 x 0.5 (For side port, use hexagon socket head set screw) N BC Note 2) For the 180 specification, the slated line area do not
With brake: 148 Without brake: 118 Housing With brake: 135 Without brake: 105 29 24.6 Thread size M3 x 0.5 6 4 45 M4 x 0.7 8 2 46 Effective thread length (mm) Quantity P.C.D.
(6) 1 2-M4 x 0.7 thread length 8 P.C.D.38 2 1 2 4 45 3 41 32 2-M3 x 0.5 thread length 8 P.C.D.29 3 Low torque Metal seal type Rotary jointSeries MQR * symbol indicates flange dimensions Dimensions/Standard Type, Flange Type MQR8-M5 MQR12-M5 0.03 7 M6 x thread length 10 4-M3 x 0.5 thread length 6 P.C.D.43 4-M3 x 0.5 thread length 6 P.C.D.48 M6 x 1 thread length 10 0.03 8 4.1 0.05depth 10
At the maximum stroke Adjustment range Maximum adjustment range Max tightening torque Nm Model Bolt MIW12D-12D M3 x 0.5 0.88 MIS12D-D MIW20D-20D MIS20D-D M5 x 0.8 4.3 23 Series MIW/MIS Specific Product Precautions 2 Be sure to read before handling. Refer to pages 16 through 18 for safety instructions, actuator precautions and auto switch precautions.
Note) Fixed unit: For vacuum/Low pressure: kPA For positive pressure: MPa Lead wire with connector Lead wire length: 2 m With mounting screws (M3 x 5L: 2 pcs.) With M3 x 8L (2 pcs.)
A B d H Model H A SN-015A M14 x 1 19 21.9 5 ZPNA-M16 M16 x 1.5 22 25.4 6 ZPNA-M18 M18 x 1.5 27 31.2 9 ZPNA-M22 M22 x 1.5 30 34.6 8 Bolts (Hexagonal Socket Head Cap Screw) Dimensions d B (mm) A B d L 8 11 5.5 M3 x 0.5 L 8 12 7 M4 x 0.7 A 10 15 8.5 M5 x 0.8 13-11-96
Circuit ZQ11U-K2D F DK With L type plug connector Type J2 ZQ11U-J2Supply valve Suction filter Bracket A (standard) 2-3.2 through Pilot exhaust port (PE port) Note 4) Body mounting hole Note 2) Air supply port (P port) Note 4) (M3 x 0.5, piping not required) (68.4) (M5 x 0.8) Vacuum port (V port) Note 4) PE (M5 x 0.8) 29.4 3 20.2 P 20.3 9.7 V Exhaust part 0.8 17.7 22.8 87.2 10 Note 1) The
How much water is crntained in 1 m3? Dew point2soo = 24glm".0.65= 15.6 g/mt When air is compressed, its capacity for holding moisture in vapor form is only that of its reduced volume. Hence, unless the temperature rises substantially, water will condense out. Erample 2: 1o m3 ol almospheric air at 15oc and 65yo r.h. is compresssd to 6 bar gauge pressure.
How to replace the shock absorber 1) Loosen the hexagon socket head set screw (M3) on the piston rod.
THRU 2 HOLES LOCATED AS SHOWN FOR M3 MOUNTING SCREW S or less.
AHC System Series MA2 How to Order AHC unit AHC unit MA 210 Y M3 N R3 Tool adapter Robot adapter Without robot adapter 8 10 11 14 15 20 Nil S1 R1 R2 R3 R4 R5 Auto hand changer Air gripper for AHC Applicable shaft diameter Transportable mass Transportable mass 3 kg 2 AHC unit Electric specifications Air connection size M3 M3 x 0.5 None N Air gripper for AHC Tool adapter <10/15> MA 210 A M3
5/32 3/8 0.04 0.12 NCRB1_W10-_S 0.55 0.20 0.35 0.02 0.20 25 0.95 1.14 0.59 0.31 0 -0.00015 (0.2) (0.26) M3 NCRB1_W10-_SE 0.33 0.37 -0.0012 -0.00045 5-40UNC 5-40UNC 0.14 10-32UNF M3 3/16 15/32 0.06 0.16 NCRB1_W15-_S 0.71 0.24 0.39 0.02 0.20 25 1.14 1.34 0.79 0.35 0 -0.00015 (0.2) (0.39) (0.24) M3 NCRB1_W15-_SE 0.43 0.39 -0.0016 -0.00045 8-32UNC 8-32UNC 0.18 10-32UNF 15/64 9/16 0.06 0.18 NCRB1
Av = Q (8) P Av : Flow coefficient [m2] Q : Flow rate [m3/s] P : Pressure difference [Pa] : Fluid density [kg/m3] (3) Formula of flow rate It is described by the practical units. Also, the flow-rate characteristics are shown in Graph (2).