SMC Corporation of America
Elite Part Number Search
Search Results "LEY25B-250"

or less Current type Input impedance Approx. 6.5k Voltage type VAC OUT Tank Approx. 2.7k Preset input ITV2090 1 to 5VDC (load impedance: 1 k or more) Set pressure (Vacuum) Vacuum pump, Ejector Analog output 4 to 20mA (sink type) (load impedance: 250 or less) Output signal Note 3) (Monitor output) NPN open collector output: Max. 30V, 30mA Switch output PNP open collector output: Max. 30mA

B: Approx 110g Sensor Supply Voltage Same as Source Voltage Connection Voltage Input 1~5V (Input Impedance: 100k) Current Input 4~20mA (Input Impedance: 250) PSE10 O P T I O N Blank (Standard) X108 PSI Display M O U N T I N G A Panel mount B Wall/DIN rail mount O U T P U T T Y P E 0 NPN 1 PNP D I M E N S I O N S PSE 51* *Dimensions refer to ones measured after R(PT) has been screwed in.

and based on the proportional relationship to these lines, the pilot air pressure for this point is approximately 0.25MPa. 40 20 1 0 2 3 4 5 6 7 Cycle (Hz) PA513 Air consumption 400 350 Air consumption l/min (ANR) SUP=0.5MPa Note 1) Even when switching cycles are changed for PA3000 with SUP=0.2MPa or PA5000 with SUP=0.2MPa or 0.3MPa, there is almost no change in the lifting height. 300 250

.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com ARX21-01 ARX21-02 0.35 0.35 IR 0.30 0.30 Outlet pressure (MPa) Outlet pressure (MPa) VEX 0.25 0.25 0.20 0.20 AMR 0.15 0.15 ITV 0.10 0.10 IC 0.05 0.05 0 0 50 100 150 200 250 300 350 400 450 500 0 0 50 100 150 200 250 300 350 400 450 500 VBA Flow rate (

Supply pressure: 0.7 MPa Set pressure: 0.2 MPa Flow rate: 0 /min (ANR) IR1000-01 IR1000-01 IR1000-01 Back pressure: 0.5 MPa Supply pressure: 0.5 MPa 0.5 0.204 0.2 Set pressure P2 (MPa) 0.4 Set pressure (MPa) Set pressure (MPa) 0.202 0.15 Set point 0.3 0.200 0.1 0.2 0.198 0.05 0.1 0.196 0 40 20 80 60 100 140 120 0 50 100 200 250 150 0 0.2 0.1 0.4 0.3 0.6 0.5 0.8 0.7 0.9 1.0 Courtesy of Steven

IFW520 125 VAC 10 to 20 25 1.5 or less 5 5 1.5 0.7 4 4 2.5 1.3 IFW550 250 VAC 20 to 50 60 3 or less 5 5 1 0.5 4 4 1.5 0.8 Note) Hysteresis is the flow rate that is necessary for moving the microswitch from the operation position (ON signal) to the return position (OFF signal). 8 VDC 7 5 3 3 5 4 3 3 5 5 3 3 4 4 3 3 14 VDC 30 VDC 5 5 3 3 4 4 3 3 125 VDC 0.4 0.4 0.1 0.1 0.4 0.4 0.1 0.1 250 VDC

, CFM x 102 l/min, CFM x 101 Display unit Note 1, 2) Real-time flow rate Accumulated flow l, ft3 x 101 0 to 50C 5% F.S. or less Operating fluid temperature Linearity Repeatability Temperature characteristics Current consumption (No load) Weight Note 3) 1% F.S. or less 2% F.S. or less 3% F.S. or less (15 to 35C, based on 25C), 5% F.S. or less (0 to 50C, based on 25C) 290 g 150 mA or less 250

Yes 3 1/2 digit LED display (Sampling frequency: 5 times/sec) 2% F .S. 1 digit or less (Ambient temperature of 25 3C) Green LED (OUT1: Light up when ON), Red LED (OUT2: Light up when ON) No-voltage input (Solid state switch or reed switch), 5 ms or longer input IP65 Operating: 0 to 50C, Stored: 10 to 60C (No condensation or freezing) Operating and stored: 35 to 85% RH (No condensation) 250

Q Breathing port: R H G SMC SMC SMC SMC N V 1/4 1/4 1/4 U 3/8 E Pitch = B Dimensions (mm) Station n-A port 2 3 4 5 Model Symbol L1 L2 L3 L1 L2 L3 L1 L2 L3 L1 L2 L3 62 93 124 155 LLC2A 75 106 137 168 146 177 208 239 73 109.5 146 182.5 LLC3A 84 120.5 157 193.5 183 219.5 256 292.5 (mm) Dimensions 94 141 188 235 A B Q C D E G H K N R S U V W Y LLC4A Model LLC2A LLC3A LLC4A LLC5A 109 156 203 250