CATALOG VC10 This do-it-yourself building block manifold is widely used in the emission analyzer and gas processing fields. The new style modules are 90% machined and drilled from bar stock. Each module can be in a center or end position in the manifold.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.
Regulator and filter regulator 1) Be sure to unlock the handle before adjusting the pressure and to lock it after the pressure is set. 2) During transport and installation, do not apply shock to the product, such as by dropping doing so will affect its precision. 3) Do not install it iin an area that is exposed to high temperature or humidity, because doing so will lead to improper operation
Unused bit is fixed to 0. 1: These alarms do not occur on the product of the cooling method -W. 2: These alarms do not occur on the product of the power specification '-20'. 3: These alarms do not occur on the product of the cooling method -A. 4.10 Register Map HRSH Series 4-20 HRX-OM-Q033 Chapter 4 MODBUS communication function 4.10.7 Circulating fluid set temperature The circulating fluid
Unused bit is fixed to 0. 1: These alarms do not occur on the product of the cooling method -W. 2: These alarms do not occur on the product of the cooling method -A. 3: These alarms do not occur on HRS200 series. 4.10 Register Map HRS100/150 Series 4-20 HRX-OM-S010 Chapter 4 MODBUS communication function 4.10.7 Circulating fluid set temperature The circulating fluid set temperature can be
Do not operate exceeding the operating pressure range. 2. Do not operate exceeding the operating temperature range. 3. Fluid Do not operate with gases. 4.
Do not mount this kit on other products. Carefully read the procedure manual included with this kit before performing the installation.
Do not expose the product to direct sunlight for an extended period of time. 1/4 12 to 14 3/8 22 to 24 3. Do not use in a place subject to heavy vibration and/or shock. 1/2 28 to 30 4. Do not mount the product in locations where it is exposed to radiant heat. 2.
Do not use tools, such as pliers, to rotate the knob. This can cause the idle rotation of the knob or damage. 3. Do not overtighten the lock nut. It is possible to tighten the lock nut (hexagon) manually. When tightening further with tools, tighten by approximately 15 to 30. Overtightening may cause breakage.
Please make sure that operating conditions do not cause problems since the use of FEP tubing under chemical environment is unsecured.
Do not use the product in a place where static electricity is a problem.
Do not touch the terminals and connectors while the power is on.
Do not apply fluid under leaking conditions. Safety cannot be assured in the case of unexpected malfunction.
Warning 1 2 Sensor Monitor PF23 4 3 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 4 8 Switch output 1 Black Output for PF23 Main circuit Pin number Content Colour 3 7 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not cut the insulator. Do not touch the terminals and connectors while the power is on. Otherwise electric shock, malfunction or damage to the product can result. Toluene 20 mm or more Sheath concentration 50% or less Hydrofluoric acid Do not touch the piping or its connected parts when the fluid is at high temperature. It may lead to burnt.
Do not use in a location having an explosive atmo sphere. 2. Do not operate in locations where vibration or im pact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 4. Do not use in environments which exceed the ambi ent temperature specifications of the product. 3.
Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3.
The received message is deleted if the calculation result and received LRC do not match. Consecutive 8 bits of the message are added, and the result without carry (overflow) is converted to 2's complement.