Parallel Style Air Gripper: Wide Type Series MHL2 10, 16, 20, 25: 40 mm, Bore size 32, 40: 80 mm.
70 4 104 Rc 1/8 Rc 1/8 62 7 7 40 125 60 32 M8 x 1.25 13 38 M12 x 1.75 depth 21 115 11 82.5 4 115 67 8 8 45 150 75 38 M8 x 1.25 14 47 WH W X Y T U V W Z Bore size (mm) 20 25 32 40 30 23 30 112 146 182 16 53 50 30 25 37 132 167 199 20 63 60 25 28.5 37 132 167 202 60 20 63 20 33 44 162 210 227 25 73 70 Without Rear Plate Stroke range (mm) Long Stroke Bore size (mm) 20 25 32 40 Bore size (mm
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
70 4 104 40 7 7 32 38 Rc 1/8 Rc 1/8 62 60 13 125 M8 x 1.25 M12 x 1.75 depth 21 115 11 82.5 4 115 45 8 8 38 47 67 75 14 150 M8 x 1.25 WH W X Y U W T V Z Bore size (mm) 20 25 32 40 30 23 30 50 112 146 182 16 53 30 25 37 60 132 167 199 20 63 25 28.5 37 60 132 167 202 20 63 20 33 44 70 25 162 73 210 227 Without Rear Plate Stroke range (mm) Long Stroke Bore size (mm) 20 25 32 40 Bore size (mm
16 53 30* 112 30 146 182 MGC 25 60 20 63 132 167 199 30* 37 60 20 132 63 167 202 37 28.5 25* MGF 70 25 73 162 44 210 227 33 20* CY1 Without rear plate Long stroke Bore size (mm) Bore size (mm) Stroke range (mm) Z R Y MY1 20 25 32 40 20 25 32 40 250 to 400 190 14 129 350 to 500 207 14 146 350 to 600 210 14 146 350 to 800 236 15 191 Note) Dimensions marked with "*" are not required for back
20 2-M6 thread depth 11 2-M6 thread depth 11 15 15 35 18 15 2-M6 thread depth 11 2-M6 thread depth 11 20 20 A 17 17 40 A 20 20 15 45 60 25 45 60 A Applicable clamp cylinder A Applicable clamp cylinder Part no.
Otherwise, injury or an accident may occur. 20 - 5. Do not put hands, etc. in between the air gripper fingers or attachments. Otherwise, injury or an accident may occur. 6. When removing the air gripper, first confirm that no workpieces are being held and then release the compressed air before removing the air gripper.
C a u t i o n ~ Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5m or smaller. ~ Take appropriate measures to ensure air quality, such as providing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of moisture can cause the malfunction of pneumatic equipment such as valves.
(Roll moment) Moment MXW25 120 70 (Static moment/Dynamic moment) Allowable Moment MXW25 70 100 50 (Nm) 30 40 Maximum moment (Nm) Maximum moment (Nm) 50 MXW20 25 30 40 Roll moment Pitch moment Yaw moment MXW20 20 Model Mr Mp/Mep My/Mey 15 MXW16 20 MXW16 12 10 15 3 5 5 MXW8 7 10 MXW12 MXW12 2 10 10 MXW12 4 5 7 5 4 3 12 20 20 MXW16 MXW8 MXW8 3 2.5 25 40 40 MXW20 2 2 1.5 50 100 200 300 500 65
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 Valve Mounting VS After confirming the gasket is correctly placed under the valve, tighten the mounting screws with the appropriate torque listed below.
Note 5) The system accuracy when combined with an applicable flow sensor.
This is included in the response from the product when there is an error in the received request. 9 NAK(15h) Error content is included in the response when there is an error in the received request. Refer to the table below for exception codes.
This is included in the response from the product when there is an error in the received request. 9 NAK(15h) Error content is included in the response when there is an error in the received request. Refer to the table below for exception codes.
The cushion effect (smooth start-up, soft stop) is not available an intermediate stop or return from an intermediate stop using an external stopper, etc. When using an intermediate stop with the above information taken into account, implement measures to prevent particulate generation and set the operating pressure to no more than 0.3 MPa.
The cushion effect (smooth start-up, soft stop) is not available an intermediate stop or return from an intermediate stop using an external stopper, etc. When using an intermediate stop with the above information taken into account, implement measures to prevent particulate generation and set the operating pressure to no more than 0.3 MPa.
Can be locked in both directions An equal holding force can be obtained on either reciprocating stroke of the cylinder. Compact lock unit is light weight and saves space Overall length has been reduced by using an independent brake cylinder (15% compared to P/A products).