To verify the gripping condition or to make any adjustments, make sure to do so in an area where the air gripper or the workpiece will not fall.
C95 CA1 CS1 Mounting Caution Plug mounting q Do not operate in such a way that a load is applied to the piston rod during its retraction. The spring that is built into the cylinder provides only enough force to retract the piston rod. Thus, if a load is applied, the piston rod will not be able to retract to the end of the stroke. Component Parts (Disassembly is not possible.)
. * Do not indicate symbol N for no lead wire on D-A3lA, A44A, G39A and K39A models. 1.4-78 Series CM2Q Application Example Designed with a low sliding resistance of the piston, this air cylinder is ideal for applications such as contact pressure control, which requires smooth movements at low pressures.
To verify the gripping condition or to make any adjustments, make sure to do so in an area where the air gripper or the workpiece will not fall.
BRAZIL SMC Pneumaticos Do Brazil Ltda. CHILE SMC Pneumatics (Chile) S.A. VENEZUELA SMC Neumatica Venezuela S.A. ASIA CHINA SMC (China) Co., Ltd. HONG KONG SMC Pneumatics (Hong Kong) Ltd. INDIA SMC Pneumatics (India) Pvt. Ltd. MALAYSIA SMC Malaysia (S.E.A.) Sdn. Bhd. PHILIPPINES SMC Pneumatics (Philippines), Inc. SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd.
For IS3100, 3110 Gasket piping side 70 5 7 12.2 18 15 5 Operating Environment 19 (Hex.) 2 x 5.5 Mounting hole 48 G 1/2 Electric wiring hole Warning 19 16 5 1. Do not use in an environment, where water or oil is splashed. Because it is the open type construction. If water or oil were to make an ingress, the electrical circuit would be corroded and result in a malfunction or damage. 2.
I EASY TO ATTACH SMALL DIAPHRAGM ACTUATORS The pneumatic and electrical ports are on the side of the body and do not interfere with the feedback lever on the other side. I STABLE OPERATION Control is very stable even on small sized actuators.
Do not use in locations where there is splashing or spraying of oils and solvents. OUT2 OUT1 3. When using a commercially available switching regulator, be sure to ground the FG terminal. SET 4. In locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port.
Do not set the mist generating pressure differential to exceed 0.2 MPa. Warning PPA 1. Before removing the oil filler plug, loosen it two and half turns to completely release the pressure in the bowl. This will prevent the oil filler plug from flying out.
When the line is stopped,do not adjust or set the differenital pressure, as it could cause the differential adjustment valve to break. 3. When setting the pressure differential, if there is a fluctuation in the operating flow rate, set the pressure differential at the lower flow rate range. ITV IC Inlet Outlet VBA VE VY1 G Piping PPA Warning Mist generation part AL 1.
Do not use the regulator with flow exceeding the Max. flow indicated in Flow Characteristics as this can cause failure in pressure adjustment. Bleed port AU AF Handle locking screw AR Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Component Parts Caution No.
To install a directional switching valve, do so on the output side of the pressure-reducing valve. 1. If drainage or debris is present in the supply pressure line, the fixed throttle becomes clogged, resulting in a malfunction. Therefore, in addition to the air filter (SMCs AF series), make sure to use a mist separator (SMCs AM, AFM series).
When piping and fittings, etc. are being screwed together, be certain that cutting chips from the pipe threads, sealing material, and other debris do not get inside the piping. Further, when pipe tape is used, leave 1.5 to 2 thread ridges exposed at the end of the pipe. 3. The unit should be mounted vertically. 4.
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.
ltil q{ry 30 (1 3/16) RailTyps DA7 o NCDBA!8363C.A5 & @l w Gommd DA8 ,n e), s63 121t2) 00 {3 1/8), 0100 (a) HailTyp DA5 O D-46 o : Available, X: Nol avilad NCDRAIBW3o-O-A7 Re e d Sw ilc h Spe c ific atio ns [od6l I}472 D{72H tra?t. BATTI D Tdl sr80 , &ttdr &r51 tr56 trt6,w D-lft Rday, Seqlericer lC CircLiil Applc.ton Rlay, Sequenc6r tc Cir!
7.1 10.6 14.1 17.7 21.2 24.7 NARM1000 NARM2000 134819 13615 13614 16.5 x 13.5 x 1.5 P7 Flow (SCFM) 7 8 9 10 11 13626 13625 13624 23 x 20 x 1.5 P8 Valve Valve spring Brass/NBR Stainless steel POM NBR NBR Pressure Characteristics Valve retainer O-ring O-ring Initial setting Supply pressure: 0.7MPa{7.1kgf/cm2} Secondary pressure: 0.2MPa{2.0kgf/c Flow: .4 SCFM NARM1000 Setting the pressure, do
Do not insert the tube when the TKS is rotating, as the pawl may be damaged. KG KFG2 MS KKA KP LQ MQR T T IDK 489
A 24 M5 thread, depth 8 With or without insert depending on base material. 32 A' Coding stud M5 x 10 DIN913-45H 12 2 8 M5 Drive flange face G1/4 DIN/ISO228/1 19.5 5.5 Solenoid valve flange face O-ring 16 x 2 1.5 IP 3 IW 1301 AW The solenoid valve can be attached with 2 mounting bolts.
DOZ is not available. 2 9 Other Option Electrical entry 3 position closed center G: Grommet Lead wire length: 300 mm L: L plug connector With lead wire LN: L plug connector Without lead wire LO: L plug connector Without connector D: DIN terminal 3 3 position exhaust center 4 M: M plug connector With lead wire MN: M plug connector Without lead wire MO: M plug connector Without connector DO
Therefore, do not operate it in an environment that is exposed to chemicals such as thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, or water-soluble cutting oil (alkalinic). 2. Operate it away from direct sunlight.