MHF2 0.2MPa 20 Example 10 When it is desired to set the gripping force at 20 times or more the workpiece weight.
The graphs are based on operation using an SMC DC power input type driver with halfstep energization.
-25 -30 CDQMB165 -10 -15 -20 -25 -30 CDQMB205 -10 -15 -20 -25 -30 -35 -40 -45 -50 CDQMB255 -10 -15 -20 -25 -30 -35 -40 -45 -50 CDQMB325 10 15 20 25 30 35 40 45 50 75 -100 CDQMB405 10 15 20 25 30 35 40 45 50 75 -100 CDQMB5010 15 20 25 30 35 40 45 50 75 -100 CDQMB6310 15 20 25 30 35 40 45 50 75 -100 CDQMB8010 15 20 25 30 35 40 45 50 75 -100 CDQMB10010 15 20 25 30 35 40 45 50 75 -100 M8 x 60L
_;aone-mK IT;frN-mTD:e7--E E-]-DE7A-fiE -fDrc76 -8.7-E ]-D:F7E]S--rD:e60]rrTD:H-7ec73C I D-C73C c0lre I D-c8oc Bole size Standard strok/Hundleths ot an inch Nole 1) Standard Auto Switch {ead wne length is 20 inchs. 1 1 I inch leads available on all mode! s by adding an L' suflix to the part number. (b(smple) D-C73 ' D-C731.
_;aone-mK IT;frN-mTD:e7--E E-]-DE7A-fiE -fDrc76 -8.7-E ]-D:F7E]S--rD:e60]rrTD:H-7ec73C I D-C73C c0lre I D-c8oc Bole size Standard strok/Hundleths ot an inch Nole 1) Standard Auto Switch {ead wne length is 20 inchs. 1 1 I inch leads available on all mode! s by adding an L' suflix to the part number. (b(smple) D-C73 ' D-C731.
HOUR METER 19 Records the accumulated time an Output or Input signal has been ON SCHMITT TRIGGER 19 Turn an Input On at the High Value and Off at the Low Value (or vice versa) ZONE COMPARE 20 Compare a value to a range of values (Analog, Direct Set, or FB values) DISPLAY * Display Messages or Data on the LCD display OFFSET GAIN 22 Manipulate Analog Values; y = A/B*x + C; Set High and Low
14 4 41 AC40-B 1/8 220.4 147.1 39.8 38.4 72.6 110 33.8 3.5 50 75.2 40 9 18 5 48 1/43/81/2 AC40-06-B 1/8 235.4 149.1 37.8 38.4 77.6 110 33.8 3 50 80.2 40 9 18 5 48 3/4 AC50-B 1/8 282.4 220.1 41.2 93.1 110 43.3 3.2 70 96.2 50 11 20 6 60 3/41 AC55-B 1/8 292.4 234.1 44.7 98.1 110 43.3 3.2 70 96.2 50 11 20 6 60 1 1 AC60-B 1/8 297.4 234.1 44.7 98.1 110 43.3 3.2 70 101.2 50 11 20 6 60 Optional
-l06 to 10 ALD900-l12 to 20 D.P.
Power cable: 1.25mm2(16AWG), External diameter: about 8 to 12mm IDF22E-20, IDF37E-20(single phase power supply) 3 cores (including grounding) IDF22E-30, IDF37E-30, IDF55E-30, IDF75E-30(3 phase power supply) 4 cores (including grounding) Additional length of about 0.2m is needed to wire inside of the product.
(Writing time: 10,000 times, Data duration: 20 years after power off) Use the clean air. This can cause operating failure. If compressed air containing condensate is used, install an air dryer or drain catch before the filter and perform drainage regularly.
Nil S n L Auto switch type Nil Without auto switch Cylinder bore size (stroke mm) Refer to the table below for auto switch part numbers. 6 8 12 16 20 25 10, 20, 30, 40, 50 10, 20, 30, 40, 50, 75 10, 20, 30, 40, 50, 75, 100 10, 20, 30, 40, 50, 75, 100, 125 10, 20, 30, 40, 50, 75, 100, 125, 150 10, 20, 30, 40, 50, 75, 100, 125, 150 Functional option Nil F R Note 2) Standard With buffer With
When using an intermediate fixing spacer for the MY3B series, the maximum operation speed is 800 mm/s (500 mm/s for the MY3B16). -10 -20 -30 -40 -50 -60 -70 -80 0 0 to 10 10 to 20 20 to 30 MY3*16/20 Without spacer Short spacer Long spacer 0 to 12 12 to 24 24 to 36 MY3*25/32 Without spacer Short spacer Long spacer 0 to 16 16 to 32 32 to 48 MY3*40/50 Without spacer Short spacer Long spacer
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
Non-locking push type [Standard type] Push in the direction of an arrow.
20 40 40 40 40 Suction flow rate Suction flow rate 10 10 20 20 20 20 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0 0 0 10 20 0 0 0 5 10 15 20 25 Supply pressure (MPa) Suction flow rate (l/min(ANR)) Supply
accurate stopping position is required, 20 11.0 consider using a metal-ended external 0.65 25 18.5 stopper. 32 30.0 40 47.0 Table 10 Allowable pressure for intermediate stops with an external stopper 5-2) Intermediate stop Fine stroke adjustment is considered as an Maximum operating pressure limit for intermediate stop, so the considerations for an Bore size intermediate stop with an external
= 20 x mg 10 x workpiece weight 20 x workpiece weight (Note) Even in cases where the coefficient of friction is greater than = 0.2, for safety reasons, SMC recommends selecting a gripping force which is at least 10 to 20 times the workpiece weight.
20 37.4 66.5 20 16 20 (38) VQ4 The broken line indicate DIN rail mounted style [-D].
x 10 With spring washer Adapter plate Note) Please contact SMC when using an individual EXH spacer assembly, an individual or an adapter plate assembly on VV5Z5-21P .
30 14 Connection thread 18.5 16.2 8 Connection thread 23.3 6 17 17.2 10.0 5 17 21 10 27.5 39.0 26.6 3 8 KGS10-03 21 19 8 1 2 KGS10-04 28 22 20 35 23 18 1 4 3 8 KGS12-02 KGS12-03 27.5 22.5 8 33.5 29 28 46.0 19 12 22 44.5 1 2 KGS12-04 20 10 30 Reference dimensions after R thread installation. 60.0 22 Note) D: Max. diameter 15-3-10 Stainless One-touch Fittings Series KG Female Connector: KGF