PFxx-OMA1007 Use a soft cloth to remove stains.
For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that cannot vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
No. 3 4 5 6 7 8 9 Note) When ordering a manifold ZZK2---A on page 3, q to e are delivered as a set.
Caution Caution indicates a hazard with a low level of risk, which if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk, which if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Stabilize the source pressure by providing a tank and a vacuum regulator. Provide a vacuum switch valve to individual lines.
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Vertical actuation (Speed control) I II P2 W A P1 a B A P0 P0 a A W (1) Basically, meter-out control is used. Combine meter-in control to reduce sudden movement. (1) Basically, meter-out control is used.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
Detaching To detach a socket from a connector, pull out the lead wire while pressing the sockets hook with a stick having a thin tip (approx. 1 mm).
P R I N G R E T U R N / S P R I N G E X T E N D NC J2 NC J2 A U T O S W I T C H C A P A B L E N U M B E R O F S W I T C H E S Not Switch Capable D Switch Capable With Built-In Magnet 2 Pieces S 1 Piece n n Pieces M O U N T I N G B O R E S I Z E See NCJ2 Accessories Section A P P L I C A B L E A U T O S W I T C H B Basic L Axial Foot F Rod Side Flange D Double Clevis (Except for 6) 6 (1/4