VND Series

External Pilot Piping of pilot port [12(P1), 10(P2)] P1 and P2 piping should be as follows according to the model. Caution Port VND0D VND02D 12(P1) External Pilot Bleed port 10(P2) Bleed port External Pilot Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention.

Clean Gas Filter

Note) Piping method should be performed in accordance with Piping in the Specific Product Precautions. 2) Operation Flush the piping line before the starting actual operation when the filter is used for the first time or has been replaced. -10- Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note:

LOCK UP VALVE

-10- -11#1 -11-11- Revision A Format change and content review B Drawings update 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2019 SMC Corporation All Rights Reserved

Precision Regulator

Panel mounting 10 7. Troubleshooting 11 8. Dimensions 12 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

Bacteria Removal Filter

Fastening torque recommended: 10+/-2Nm 5-6. Start of operation Before actual operation, confirm there is no leakage. If there is leakage, remove the element after stopping the operation. Clean the seating surfaces, check and replace the O-ring and tighten the cover. -10- Doc. No. SF-OMZ0013-B 6. Dimensions -11- Doc. No. SF-OMZ0013-B Revision history Rev.

ITV2-OM00114

(Tightening torque 0.6 to 0.8Nm) Dipswitch ON 1 2 1 2 3 4 5 6 7 8 9 10 SW40 SW20 SW10 SW08 SW04 SW02 SW01 BS4 BS2 BS1 Hold/Clear Terminating resistor Setting at the time of shipment 1 2 1 2 3 4 5 6 7 8 9 10 Node address: 1 Baud rate: 10Mbps Hold/Clear: Clear Terminating resistor: disable Setting of node address Node address SW40 SW20 SW10 SW08 SW04 SW02 SW01 1 OFF OFF OFF OFF OFF OFF ON 2

SYJA5000 Series

S: Effective sectional area (mm Air temperature() -20 -10 0 10 30 40 50 60 Correction coefficient 1.08 1.06 1.04 1.02 0.98 0.97 0.95 0.94 SYJ5000-OMJ0001-A -6- TROUBLESHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.

VF1000/3000/5000 Series (PILOT VALVE : V200)

Operation in a low temperature condition It is possible to operate a valve in extreme temperature, as low as -10 . Take appropriate measures to avoid freezing of drainage, moisture etc. in low temperature. 7. Mounting orientation Mounting orientation is free. Design / Selection 3.

VNC/VNH Series

Warning Warning Caution External Pilot Pilot port 12(P1) and 10(P2) piping P1 and P2 piping should be as follows according to the model. Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention. Caution Mounting 1. Do not apply external force to the coil section.

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?

10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?