Ionizer Gun It may cause injury to personnel. 5) Do not use the product to clean or remove toxic substances or chemicals. 6) Do not drop, step on or hit the product.
Do not use tubing which do not meet these outside diameter tolerances. It may not be possible to connect them, or they may cause other trouble, such as air leakage or the tubing pulling out after connection. -14SY3000*-OMJ0003-A Specific Product Precautions 8 Be sure to read before handing.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Low-frequency operation 3.
Note) Do not pull on the lead wires with excessive force. This can cause faulty and/or broken contacts.
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. Operate after safety is confirmed. 5. If the volume of air leakage increases or the valve does not operate normally, do not use the valve.
Do not disassemble the product or make any modifications, including additional machining. Doing so may cause human injury and/or an accident. 14.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of auto drain will stop and water will flow out through the air outlet.) When tightening piping at the air inlet/outlet tube, the nozzle should be held firmly with a pipe wrench.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.
Wrapping of sealant tape When screwing together pipes and fittings, etc., be certain that chips from the pipe threads and sealant material do not get inside the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. Operating Environment Warning 1. Do not use in environments where there is a danger of corrosion.
Do not use this product in the presence of dust, particles, water, chemicals, and oil. Use with such materials is likely to cause a malfunction or breakage. 2. Do not use this product in the presence of a magnetic field. Use in such an environment is likely to cause a malfunction. 3. Do not use this product in an atmosphere containing an inflammable gas, explosive gas, or corrosive gas.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Do not use this product in a location where vibration is not allowed. 5. Actual speed of the product can be changed by load. When selecting a product, check the catalog for the instructions regarding selection. 6. Do not apply a load, impact or resistance in addition to a transferred load during returning to the original position.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3.
Do not cut the tube with pliers, nippers, scissors, etc.
In such cases, it is recommended to use a dual speed controller. 3) Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals etc. will result in leakage or malfunction. 4) Do not dent or scratch the mounting surface of the body and the plate.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble and modify. It may result in the trouble, malfunction, fire, etc. 2. Do not touch for a while when being energized or after cutting off the power source because it is high temperature. 3.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Operating environment Do not use in operating conditions or environments where changes in color or deterioration of material due to corrosion occur. Do not use this product in a place where shock or vibrations occur. Do not use the hydraulic filter outdoors.