HAA Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Leave 29 mm of the electric wire and 12 mm of the braided shield wire. Note Please do not use it for purposes other than the original purpose. This connector may only be operated when under no load. Working with wet hands causes electric shock. Please never perform a repair.
When the element comes to the end of its life immediately replace it with a new filter or replacement element (cartridge type). 4 Do not disconnect and replace the one-touch fitting. Environment Warning Warning 1. Do not use the product in the following environments, which could cause failure. Seals the element, cover and fitting body. A place exposed to water, steam or oil.
(from ITV to PLC) Resolution : 12bit (100%F.S.), Occupied byte : 2 Byte Output pressure (I area) 12bit 0 0 0 0 Output pressure (Lower 12 bits) * b0 b15 b11 (note) Monitor the product error. 7 bytes are occupied for external diagnosis data. Allocate data below to 7th byte as a diagnosis.
Do NOT make upward piping. 2. Float type auto-drain (N.C.) DO NOT pipe upwards. (ANR)}. 2) Set pressure more than 0.1 MPa. 2. Float type auto-drain (N.C.) 1) Compressor can be used even if energy is under 3.7 kw. 2) Set pressure more than 0.15 MP 14-3-14
Do not place a magnetic object near the pressure switch. Unintended operation may result. 2. Do not apply strong shocks (over 300 m/s2) to the pressure switch to prevent the switch from damage. AV AU AF Caution Flow rate (/min (ANR)) Inlet pressure (MPa) 1. Release the lock to adjust the pressure. After the adjustment, engage the lock.
Definition of Symbols Mounting SlA Warning aConditions for mechanical operation Do not move the mechanical operation beyond the operating limit position, as this could damage the mechanical valve itself and lead to equipment malfunction. OActuator Stroke Operate the mechanism within the stroke range that has been obtained through the formula given below.
Before piping and screwing in couplings, please make sure that sludge trom pipe threading and sealing materials do not go into the pipe. When seal tape is used, tape winding should be done so that 2 threads are left untaDed on the end.
S Z With surge voltage suppressor (Grommet type only) With light/surge voltage suppressor (Not possible with grommet type) Port size Electrical entry 1/4 (AV2000 only) 3/8 (AV3000 only) 1/2 (AV4000 only) 3/4 (AV5000 only) 1 (AV5000 only) 02 03 04 06 10 G: Grommet Coil rated voltage 1 2 3 4 5 6 7 9 100 VAC (50/60 Hz) 200 VAC (50/60 Hz) 110 to 120 VAC (50/60 Hz) 220 VAC (50/60 Hz) 24 VDC 12
Cover both sides 2 pcs. 6 12 6 12 KQB2 Tubing O.D. Type KS KX Multi-connector Plug side only Socket side only Nil P S 23 04 3.2 4 KM KF Precautions M Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages 13 to 17 for Fittings and Tubing Precautions.
entry Port 1(P), 2(A) 3(R) 1 8 1 8 01 1 02 G Grommet (Lead wire length 300 mm) 1 4 1 4 H Grommet (Lead wire length 600 mm) 1 4 1 4 02 3 03 D DIN terminal 3 8 3 8 DO DIN terminal (Without connector) 04 1 2 1 2 1 2 3 4 1 2 3 4 1 04 5 06 Body ported G Grommet (Lead wire length 300 mm) 10 1 1 1 H Grommet (Lead wire length 600 mm) 10 7 12 14 9 20 2 E Grommet terminal 1 4 1 T Conduit terminal
Pilot valve symbol 200 AC 110 AC 220 AC 12 DC 100 AC 24 DC q K1 K1 K2 J1 J1 J2 Q1 Q2 N1 N2 Nil Y w e Nil r Nil Y t y Nil u Nil i Nil o Nil !0 Nil Combinations q to !
Do not apply force when transferring, mounting and dropping the regulator with a pressure gauge. This may cause misalignment of the pressure gauge pointer. AP100 Precautions for IR2120, IR3120 (air operated type) only Caution 1.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
Before piping and screwing in couplings, please make sure that sludge trom pipe threading and sealing materials do not go into the pipe. When seal tape is used, tape winding should be done so that 2 threads are left untaDed on the end.
Applicable filter model Element size mm Principal Materials ZFC100 12 x 8 x L20 I-62S ZFC101 Description Material ZFC200 16 x 12 x L25 I-63S Case Special transparent nylon ZFC201 Cover PBT Note) When ordering spare elements, enter "-A" at the end of the part number. Spare elements and O-rings for the cover are sold in sets of 10 pieces each.
Do not place a magnetic object near the pressure switch. Unintended operation may result. 2. Do not apply strong shocks (over 300 m/s2) to the pressure switch to prevent the switch from damage. AV AU AF Caution Flow rate (/min (ANR)) Inlet pressure (MPa) 1. Release the lock to adjust the pressure. After the adjustment, engage the lock.
For the VV5QC11: VVQ1000-80A-1 (12 pcs. per set)
For the VV5QC21: VVQ2000-80A-1 (12 pcs. per set)
For the VV5QC41: VVQ4000-80A-1 (10 pcs. per set)
For the VV5QC51: VVQ5000-80A-1 (10 pcs. per set)
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
Piping: Common SUP/Common EXH, Stations: 12 Stations, Bracket: -