New Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 2. When problems are caused by a water hammer, install water hammer relief equipment (accumulator etc.), or use an SMC water hammer relief valve (Series VXR). Please consult with SMC for details. 5.
Do not use it in such a way that excessive external force or impact force could work on it. This could result in damage. Caution 1. Do not scratch or dent the mounting side of the body, table or end plate. The damage will result in a decrease in parallelism, vibration of the guide or an increase in moving part resistance. 2.
(If you do not the power to OFF, it does not reflect the data in the driver.) Note2) Selected Items Write: It writes the parameter values of the corresponding frame to the driver. Single Axis Write: It writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
(If you do not the power to OFF, it does not reflect the data in the driver.) Note2) Selected Items Write: It writes the parameter values of the corresponding frame to the driver. Single Axis Write: It writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Safety Instructions Warning Do not disassemble, modify (including the replacement of the circuit board) or repair the product. Do not use the components other than the specified components. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Otherwise, the operation of an auto drain will stop and drainage will discharge through the air outlet.) If it is unavoidable that the tube goes upward, make sure it only goes as far as the position of the auto drain outlet.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Confirm model no., size, etc. before installing. Check tubing for damage, gouges, cracks, etc. The fluoropolymer tubing do not have the model number displayed on the product due to the resin material used.
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specifications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specified procedures.
Failure to do so may cause the angle adjusting screw to become loose or drop.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water vapor, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not allow pallets to strike the lever when it is standing up. Do not allow pallets to strike the lever when it is standing up (after the shock absorber has absorbed energy), because the cylinder body will be subjected to the full energy of the impact. 2. Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc.
Rotation should be controlled by connecting it to another shaft (linear guide, etc.). 3.Do not operate with the magnetic coupling out of position.
Sensor shall be inspected by experienced person with adequate knowledge. (2) Do not overhaul nor modify to avoid electric shock, failure, fire, etc. Overhauled or modified product does not guarantee spec. function or performances. Warning Handling ! (1) Do not drop, hit nor apply excess impact(100m/s2 or more).
Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. 2. If using in a location directly exposed to sunlight, shade the product from the sunlight. 3. Do not mount the product in locations where it is exposed to radiant heat. 9 4. Do not use the product in a place where static electricity is a problem.
However, do not use the product under water.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Do not use any form of sealant other than the tape type of sealant. 3Winding of sealant tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not enter the piping.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.