e Do not use in a place where a magnetic field is present. It may cause malfunction to the actuator. 3. Do not use the product in the presence of flammable, explosive or corrosive gas. It may cause fire, explosion, and corrosion. The actuator does not have an explosion proof construction. 4. Do not use in an environment subjected to temperature cycle.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (490 m/s2) while handling. Although the external body of a switch (switch case) may not be damaged, the switch inside could be damaged and cause a malfunction. 2. Do not use until you can verify that equipment can operate properly.
Do not apply external force to the coil. Apply a wrench to the exterior surface of the piping joint at the time of tightening. Do not use heat insulators, etc. to keep the temperature at the coil assembly. Do not use a tape heater for freeze prevention except on the piping and body. If may cause the coil to burn.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not remove or rub off danger warning labels. Cimfirm the positions of danger warning labels. CAUTION !
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use in environments where there is a danger of corrosion. 2. Do not use in direct sunlight. 3. Do not operate in a location subject to vibration or impact. 4. When using auto switches, do not operate in an environment with strong magnetic fields. 5. Grease base oil can decrease depending on external environment and operating conditions.
If any valves are used ensure that they do not restrict the flow, otherwise low flow may cause an alarm. Target Temp.
Do not stare into beam visible at XF1/XF2.
Do not apply a load in excess of the operating limit. 1. Do not allow the table to hit the end of stroke. A product should be selected based on the maximum load and allowable moment.
Do not open the cushion valve beyond the stopper. A snap ring is installed as a cushion valve retention mechanism. Do not open the cushion valve beyond it. If not operated in accordance with the above precautions, the cushion valve may be ejected from the cover when air pressure is supplied.
Warning If any error occurs, do not start operating the product.
Do not use the product in an environment subject to a temperature cycle. It will cause failure of the controller or its peripheral devices. 15. Do not use the product in a place where surges are generated.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not use in direct sunlight. 8. Do not mount the product in locations where it is exposed to radiant heat. 9. Take appropriate measures against the lightning surge on the equipment side as the auto switches do not have any lightning surge resistance specified in the CE marking. Caution 1.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.