Stainless Steel Heat Assembly is required. 7 Technical Data Pressure dew point Condensed water calculation Atmospheric pressure 45 Relative humidity 100% 40 0.1MPa Amount of water in air g /m3 35 80% 60% 0.2 40% 0.3 0.4 0.5 30 0.6 0.7 0.8 25 Amount of condensed water 20% 3 8 1.0 18.2 3.0 = 15.2g/m3 20 2 3 4 1.5 15 10 5 8 7 3.0 1 6 0 5 Intake air temperature C (atmospheric pressure) Air temperature (Pressure
CUX16-PS Proper tightening torque (Nm) (cylinder body) 10 16 20, 25 32 Hexagon socket head cap screw size (mm) M3 Bore size (mm) Rod seal 1 pc. CUX20-PS Gasket 1 pc. CUX25-PS 0.5410% Grease pack (10g) 1 pc. CUX32-PS M4 1.2310% Seals cannot be replaced for 10mm bore size. M5 2.5510% M6 4.0210% 2.
Remove pilot valve mounting screws (M3, 2 pcs.), rotate the pilot valve at 180 and then re-tighten the valve with the screw.
The mounting dimensions (in the drawing below) are identical with those of existing NCY2B series, allowing easy replacement. ( For bore size of 6(1/4"), the mounting is not directly interchangeable with the NCY2B series because the piping port has been reduced to a M3 size.)
Hexagon socket head bolt (M3 x 4L) Auto switch Auto switch mounting bracket Auto switch mounting nut Note 1) The torque for tightening the hexagon socket head bolt (M2.5 x 9L) is 0.2 to 0.3 Nm. Note 2) The torque for tightening the hexagon socket head bolt (M3 x 4L) is 0.5 to 0.7 Nm. Auto Switch Mounting Bracket Part No.
screw (M3 x 0.5 x 10l ) Switch spacer Switch mounting nut Data 50 25 to 600 BQ-2 63 25 to 600 Please contact SMC regarding non-standard strokes.
MVGQ 10 16 20, 25 32 0.54 10% M3 CUX32-PS Grease pack (10 g): 1 pc. 1.23 10% M4 It is impossible to replace seals in bore size 10 mm. CC 2.55 10% M5 4.02 10% M6 2. Grease pack When maintenance requires only grease, use the following part numbers to order. Grease pack GR-L-005 (5 g) GR-L-010 (10 g) GR-L-150 (150 g) RB Operating Precautions J Warning 1.
A Mounting screws (M3 x 8L) (accessory) Waterproof seal (accessory) Panel mount adapter Power supply/Output connection cable ZS-26-A Panel Front protective cover + Panel mount B Mounting screws (M3 x 8L) Front protective cover (accessory) Waterproof seal (accessory) Panel mount adapter Panel Options When only optional parts are required, order with the part numbers listed below.
Be aware that the output circuit is not active immediately after the power is connected. 3.1-12 PSE100 Dimensions A: Panel mount 56 l50 Gasket (Accessory) 7.4 l48 PRESSURE SWITCH 10 8 l 45 A Panel mount adaptor (Accessory) 55 11.4 Cover for display (Optional) 62 4 X 7.5 (= 30) 6.5 7.5 10-M3 2-M3 X 8L 30 View A Cutout dimensions for panel mount 65 or more 45 +0.6 0 +0.6 0 45 +0.6 0 N pieces
Mist generation pressure differential (MPa) IC EX: How to obtain the mist generating pressure differential if the flow rate obtaine in 1. above is 35 m3/min and the line pressure (inlet pressure P1) is 0.7 MPa: Extend horizontally from the point at which the flow rate is 35 m3/min to obtain the point that intersects with P1 = 0.7 MPa.
Real-time switch output ( ) Unit switching Hysteresis mode Display Real-time flow rate l/min Accumulated flow l ZSE ISE ON YES OFF P-1 P-2 GPM gal (US) PSE Real-time flow rate GPM = gal (US)/min P Window comparator mode H: Hysteresis Z I SE3 Note) Fixed SI unit (l/min, l, m3 or m3 x 10) will be set for the type without the unit switching function.
Mounting screw (M4) Terminal block cover M3 screw Gasket 6mm Electrical entry 2-G3/4 Step 3. How to replace the terminal block cover Securely tighten the screws to the torque shown in the table below, after confirming that the gasket is installed correctly.
Hexagon socket head cap screw (M3 x 0.5 x 16l) 2 pcs.
Real-time switch output Unit switching Hysteresis mode ON YES Display Real-time flow rate Accumulated flow OFF P-1 P-2 L/min L Real-time flow rate GPM gal (US) "P" Window comparator mode H : Hysteresis GPM = gal (US)/min H H Note) Fixed SI unit (L/min, L, m3 or m3x10) will be set for the type without the unit switching function.
Note Auto switch mounting screw (M3 X 0.5 X 6.5l) Switch mounting nut 25, 32, 40, 50, 63 BMU1-025 Mounting Bracket/Part No. Mounting screw set made of stainless steel Following stainless steel mounting screw set (included nut) is provided. Use them with accordance to environment. (Auto switch interface is available. Order it separately.)
A Mounting screws (M3 x 8L) (Accessory) Waterproof seal (Accessory) Panel mount adapter Power supply/Output connection cable ZS-26-A Panel Front protective cover + Panel mount B Mounting screws (M3 x 8L) Front protective cover (Accessory) Waterproof seal (Accessory) Panel mount adapter Panel Option When only optional parts are required, order with the part numbers listed below.
Signal Cable Specications Power cable Terminal specications Cable specications Terminal block screw diameter Recommended crimped terminal 0.75 mm2 (AWG18) Shielded cable M3 Y-shape crimped terminal 1.25Y-3 Signal cable 15 Partially enlarged view A Series HRS100/150 Thermo-chiller Standard Type List of Function Operation Display Panel The basic operation of this unit is controlled through
(Tightening torque of M3 screw should be 0.5 to 0.7 Nm.) 5. Modification of the detecting position should be made in the condition of 3. Auto switch Auto switch mounting nut Auto Switch Mounting Bracket Part No.
KJS04-M3 KJL04-M3 Refer to Construction. (page 853) Symbol 0 2 5 Without fitting (M3 x 0.5) 4 (Straight) 4 (Elbow) Without supply Note) adapter (For manifold) Pilot valve (Refer to Table (1).) M Standard (1 W for DC) Note) Nil Y DC low wattage type (0.5 W) Note) Note) O-ring and round head combination screws (M2 x 12) are attached to the supply adapter (M).
Thread sizes range from M3 to 2 and are available in both inch (NPT) and metric R/Rc(PT)Speed controller standard in-line style, Body sizes: M3, M5, 1/8, 1/4, 3/8, 1/2, Port sizes: M3, M5, 01, 02, 03, 04, SPEED CONTROL IN-LINE, AIRLINE EQUIPMENT, AS FLOW CONTROL, 1B, AS OTHER SIZE STANDARD (PT), 1.25978 lb, ModelPort sizeFree flowControlled flowApplicable cylinder bore size (mm)Weight