VNB Series Warning Pilot port piping 12(P1) and 10(P2) piping should be as follows according to the model Standard () If the pilot air is not supplied, the valve position will not be held. Pressurize Port 12 (P1 ) or Port 10 (P2) when using the product. Vacuum pilot Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention.
Order no. 1.5 m SAC-3P-1,5-PUR/M 8FR 1669738 3 m SAC-3P-3,0-PUR/M 8FR 1669741 5 m SAC-3P-5,0-PUR/M 8FR 1669631 10 m SAC-3P-10,0-PUR/M 8FR 1694169 Solenoid valve side pin wiring diagram 1 (+, ) Energy saving IC 3 (, +) Diode 3 (, +) 1 (+, ) LED Coil There is no grounding for this product.
Related Products Ambient and fluid temperature (C) Weight (g) Note) Bracket assembly Dust bag assembly 417 (436) ZH-BK1-20-A ZH-DB1-20-A 929 (990) ZH-BK1-30-A ZH-DB1-30-A 1847 (1966) ZH-BK1-40-A ZH-DB1-40-A 92 (101) ZH-BK1-10-A ZH-DB1-10-A Note) ( ): Weight including the bracket Flow Rate Characteristics ZH10-X185 ZH20-X185 ---7 ---7 1,800 800 Suction flow rate [L/min (ANR)] Note 1) Air consumption
e 00 10 20 30 40 50 60 70 80 90 100 110 Vacuum pressure 50 kPa (qwe) = Suction flow (Q1) 31 l/min (ANR).
Loop through current between power connector 16 A or less (EX245-FPS1/2) 10 A or less (EX245-FPS3) OFF 3 2 US2 [US3, US4 .. etc] is below the permissible level but above the dropout level (17 to 21.6 VDC). Flash Operating voltage 24 VDC +20%/-15%, Class 2 1 ON US2 [US3, US4 .. etc] is present (> approx. 22.8 VDC).
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2015 SMC Corporation All Rights Reserved EX-OMS0018
If the total lifting height is required instead of the discharge pressure, a discharge pressure of 0.1 MPa corresponds to a total lift of 10 m. Selection procedures: 1. First mark the intersection point for a discharge rate of 27 L/min and a discharge pressure of 0.25 MPa. 2. Find the pilot air pressure for the marked point.
If the total lifting height is required instead of the discharge pressure, a discharge pressure of 0.1 MPa corresponds to a total lift of 10 m. Selection procedures: 1. First mark the intersection point for a discharge rate of 15 L/min and a discharge pressure of 0.14 MPa. 2. Find the pilot air pressure for the marked point.
INR-244-831 3-1 Communication Format 3.3 Composition of Required Message (from master to the product) Refer to page 3-4 3.5 Explanation of Code for codes 1 to 10.
Fluctuation of each voltage should be +/10% or less. Selection Caution All models 1. Keep within the specified range of the pilot pressure. 2. Fluid containing foreign matters and oil will cause malfunction and sealing failure. Remove such things from the fluid. Mounting Caution All models 1. In high humidity environments, keep the valve packed until the time of installation. 2.
MWP*-OM0020Q-B PRODUCT NAME Air Press Cylinder MODEL/ Series/ Product Number MWP Series Contents Safety instructions 2,3 ActuatorsPrecautions 48 Air Press Cylinder Specifications Specifications 9 Operation Principle 10 Relationship between the output and stroke 10 Installation and Handling Mounting Orientation / Installation 11 Application Examples 11 Cylinder Replacement 12 References 12,13
How to set up data 8 6.1 Easy setup Screen 8 6.2 How to setup data 10 6.2.1 Operation mode setting 10 6.2.2 How to setup in-position operation (Numeric setting) 11 6.2.3 How to setup in-position operation (at cycle time setting) 12 6.2.4 How to setup pushing operation 14 6.2.5 How to set jog and inching in position setting 16 6.3 Drive test 17 6.4 Confirmation of Operating waveform display
FGD-KT002 FGDE Nut kit FGD-KT003 FGDT FGD-KT004 FGDF FGD-CV005-03 FGDT,F-03 FGD-CV005-04 FGDT,F-04 FGD-CV005-06 FGDT,F-06 Replacement cover (5) FGD-CV006-03 FGDC,E-03 FGD-CV006-04 FGDC,E-04 FGD-CV006-06 FGDC,E-06 Joint FGD-OP001 FGDB (10) KT-FGDC FGDC Each of (2)(4)(6)(13) and (16) are provided as a kit.
Continuous Duty Valve Mounting When the product is continuously energized for a long period of time (10 minutes or longer), select the low wattage type (DC specification). After confirming that the gasket is installed correctly, securely tighten the mounting screws according to the tightening torque shown below.
Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country. 3 No.VT325-OMK0002-B VT325 Series 3 Port Solenoid Valve Precautions 1 Be sure to read this before handling products. 10.
Y terminal: Up to 1.25-3Y of Japan Solderless Terminal Rod terminal: Up to size 1.5 10 SGC200-OMM0002-F SGC / SGH Series Coolant Valve / Precautions 8 Be sure to read this before handling.
Correlation between input number and Input Block The total number of Input and Output blocks can not exceed 10. The maximum input point is 32.
Name Material Remark 1 Body A PBT 2 Body B Brass Electroless nickel plating 3 Handle POM 4 Needle POM 5 End cover Brass Electroless nickel plating 6 Spring Steel wire 7 U-seal HNBR 8 O-ring NBR 9 Needle O-ring NBR 10 Y seal NBR 11 Seal for fitting NBR 12 Cassette 16 Seal NBR For G thread only. 11 - Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249
(Tightening torque 0.6 to 0.8Nm) Dipswitch ON 1 2 3 4 5 6 7 8 9 10 Enable or disable of Dip switch MAC ID Baud rate HOLD/CLEAR Setting at the time of shipment 1 2 3 4 5 6 7 8 9 10 Node address: 0 Baud rate: 125kbps Hold/Clear: Clear Dip switch: enable 8 - Setting of MAC ID MAC ID 1 2 3 4 5 6 0 OFF OFF OFF OFF OFF OFF 1 OFF OFF OFF OFF OFF ON 2 OFF OFF OFF OFF ON OFF : : : : : : : 62 ON ON
When a current of approx.150 mA or more is applied, the over current circuit will operate, Er.5 will be displayed and the operation will stop. 1Brown 1Brown Power supply Power supply DC24V+/-10% DC24V+/-10% 2White 2White 3Blue 3Blue Load Load 4Black 4Black Please install a load to give an output current of 80 mA or less.