Manifold Specifications Unused Lead wire assy U side 6 stations (14 stations) Pin Confirm an insertion of the lead wire assembly after the insertion of pin by light pulling of the lead wire. (n) 4. Mount the end plate !2 and !3 and tighten the bolt !1. 7 stations (15 stations) (2) (1) Stations Note 1) Be careful that the packing and the O-ring do not fall out of the groove.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) SW1 SW2 SW3 SW4 SW5 SW6 Node ID Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Refer to the valve catalogue for valve manifold dimensions. 1 ASInterface line (+) AS-i + 2 4 (0 V) RESERVE 2 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Pin Allocation 4 Over current protection Yes 1 UT1 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. SF and BF Indicators Yes Over current detection 2 DI (Input signal "n+4") FS LED 3 1 BF SF Description 3 0V (US1) Fieldbus Do not operate the product outside of the specifications.
Input (Only connector "0") 2 1 2 Input No.1 1 3 Power supply (0 V) 1: Input No.1 is connected to the pin No.2 of the input connector "0", 2 input signals can be directly inputted the input connector "0". 2: N.C.: Not connected 5 3 4 Input 4 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. EX9-PE1 power input connector No.1 M12 5-pin plug B-code Element No.
Caution Operating Condition (1) Do not use in atmosphere containing corrosive gas, chemicals or exposed to sea water or vapor. (2) Do not use where vibrate or exposed to impact. (3) When heat source exist nearby, protect the regulator from the radiation heat.
Warning Environment (1) Do not use in environment where the product is exposed to corrosive gas, chemicals, salt water, water or steam. (2) Do not operate the product in a location where it is subject to strong vibration and/or shock. For vibration, it should be within 1G 60Hz. ! ! ! ! -6- 7. Maintenance Warning (1) If handled improperly, compressed air can be dangerous.
Connection 1) Rc connection Confirm that chips from the pipe threads and sealing material do not enter the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. -4- Piping Piping 2) TSJ connection The TSJ fitting is a kind of a self-align fittings.
Warning Environment (1) Do not use in environment where the product is exposed to corrosive gas, chemicals, salt water, water or steam. (2) Do not operate the product in a location where it is subject to strong vibration and/or shock. For vibration, it should be within 1G 60Hz. ! ! ! ! -6- 7. Maintenance Warning (1) If handled improperly, compressed air can be dangerous.
Do not operate under the conditions listed below due to a risk of malfunction.
When mounting the load with screws, do not exceed the maximum tightening torque. (The torque may vary depending on the material of the load.) Bolt Model Maximum tightening torque (Nm) Caution MGJ6 M2.5 x 0.45 0.5 MGJ10 M3 x 0.5 1.0 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals can cause air leakage or malfunction, etc. 2.
Mounting from upper side l l Model Bolt Maximum tightening torque (Nm) l (mm) MGF 40 MGF 63 MGF100 M6 x 1 10 7.5 M8 x 1.25 25 9 M10 x 1.5 51 9 Mounting from bottom side Do not bring objects that are sensitive to magnetism near the cylinder. There is a magnetic built into the cylinder. Do not bring magnetic disks, cards, or tapes near the cylinder. Data may be lost.
Although switches satisfy the IEC standard IP67 structure (JIS C0920: anti-immersion structure) (except D-A3l, A44l, G39l, K39l), do not use switches in applications where they are continually exposed to water splash or spray.
Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
Do not supply lubrication, as this is a non-lube product. The interior of the cylinder is lubricated at the factory, and lubrication with turbine oil, etc., will not satisfy the product's specifications. 6. Never reapply lubricant. Never reapply lubricant, as there may be a degradation of particulate generation or operation characteristics. 2.
Use under conditions where pressure fluctuations (pulsations) exceeding 0.1 MPa do not occur. Operating pressure MAX. 0.99MPa Vacuum 1.310-6kPa Operating temperature 5oC to 80oC Element proof differential pressure MAX. 0.1MPa Element reverse differential pressure MAX. 0.05MPa Not possible to use with connecting in reverse.
Use under conditions where pressure fluctuations (pulsations) exceeding 0.1 MPa do not occur. Operating pressure MAX. 0.99MPa Vacuum 1.310-6kPa Operating temperature 5oC to 80oC SFB10MAX. 0.5MPa Element proof differential pressure SFB20-02 MAX. 1.0MPa SFB10MAX. 0.07MPa Not possible to use with connecting in reverse.
Connection 1) Rc connection Confirm that chips from the pipe threads and sealing material do not enter the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. -4- Piping Piping 2) TSJ connection The TSJ fitting is a kind of a self-align fittings.
Operating Environment Warning (1) Do not operate under the conditions listed below due to a risk of malfunction. In locations having corrosive gases, organic solvents, and chemical solutions, or in locations in which these elements are likely to adhere to the equipment. In locations in which salt water, water, or water vapor could come in contact with the equipment.