Centering Unit 12 mm (MACM2) 20 20 mm (MACM4) 30 30 mm (MACM6) 50 50 mm (MACM10) Nil Unsupported P Port side photo sensor mounted type B Port back side photo sensor mounted type Specications Precautions Model MACM2-12 MACM4-20 MACM6-30 MACM10-50 Max. allowable load weight lbf [KN] 450 [2] 900 [4] 1350 [6] 2250 [10] Be sure to read this before handling the products.
) Weight (kg) 10 13 18 10 13 18 12 15 20 Internal capacity (L) 14 21 29 14 21 29 11.5 18.5 26 Note 1) Cannot be used with gases.
Parts replacement procedure 12 1 XL-OMM0005-A Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
a) .250 \-24 0.50 .624 .621 0.25 0.86 0.38 it-l6 .251 .zfi 0.75 0.25 o.34 It.oo o.75 o.62 o.12 # 1 8 o.75 1-?
VEX312 VEX332 1 100 VAC (50/60 Hz) 2 200 VAC (50/60 Hz) 3 110 VAC (50/60 Hz) 4 220 VAC (50/60 Hz) 5 24 VDC 6 12 VDC V 6 VDC S 5 VDC R 3 VDC * DC specification of type D and DO is only available with 12 and 24 VDC. 32 02 1/4 03 3/8 04 1/2 Foot bracket ( VEX312 and VEX332 only) F N* Pilot exhaust (PE) silencer Electrical entry Grommet L plug connector M plug connector DIN terminal G: Lead
Recommended torque: 12 to 14 Nm.
Precautions Do not turn off the controller for communication while the setting software (ACT Controller) is running. Do not connect or disconnect the cable while the setting software is running. The communication is continuously established while the setting software is running.
Tidy Un-friendly What do you think to the manual presentation? ! ! ! Yes Not too bad Unusable Are the explanations understandable? Which explanation was most difcult to understand: . . ! ! Are there any diagrams which are not clear? Yes No If so,which:. ! ! ! What do you think to the manual layout?
Do not touch the LCD indicator face of the pressure switch during operation. Static electricity will cause malfunction or damage to the internal parts. Pressure Setting 1.
Do not block the bleed hole. If the bleed hole is blocked, the product will not operate properly. VBA VBAT AP100 875
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not use tools on the pressure regulator knob as this may cause damage. It must be operated manually. Pull the pressure regulator knob to unlock. (You can visually verify this with the "orange mark" that appears in the gap.) Push the pressure regulator knob to lock.
Do not use in locations where there is splashing or spraying of oils and solvents. Since this unit is open type, if water or oil, etc. make an ingress etc., the internal circuit may be corroded and result in a malfunction or damage. 2. Ground the piping when induction noise is expected to be generated from piping.
Do not use in locations where there is splashing or spraying of oils and solvents. Since this unit is open type, if water or oil, etc. make an ingress etc., the internal circuit may be corroded and result in a malfunction or damage. 2. Ground the piping when induction noise is expected to be generated from piping.
Do not attempt to rotate, as it does not turn Cable connection threads RC(PT) 1/4 Exhaust porl EXH (3) Port size 4-M5 x 0 8 thread depth 6mm Mounting hole 2-RC(PT) 1/4, 3/8 SUP port, OUT porl rTl|z000/3000 tleflru-Pltotllnalic Re[ula 0imeffiiolt$ ITV3OtrT Cable connector (4 wire) Cable connector (4 wire) . Do not anempt to rotate. as it does not turn.
not assembled. 3 4(A), 2(B) port size M5 M5 x 0.8 C4 C6 One-touch fitting for 4 One-touch fitting for 6 3 position exhaust center 3(R) port PE port Note) 1(P), 5(R1), 3(R2) port: M5 x 0.8 4 Rated voltage Manual override 1 2 3 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 110 VAC, 50/60 Hz 220 VAC, 50/60 Hz Nil: Non-locking push type C: Locking type C (Manual) 3 position pressure center 4 5 24 VDC 12
Do NOT make upward piping. 2. Float type auto drain (N.C.) 1) Compressor can be used even if energy is under 3.7 kW. 2) Set operating pressure more than 0.15 MPa. 2. Float type auto drain (N.C.) DO NOT pipe upwards. 446 SP093-001I Issued: Sep 2009 P.G.
Do not subject the gauge to impacts, such as dropping, during transportation and mounting. This can cause loss of indication accuracy. 2. Do not use in locations with high temperature and humidity. This can cause malfunction. 3. When screwing the pressure gauge into place, be sure to apply your wrench on the square wrench flats.
Do not dispose this fluid in the environment.
Lock keys (refer to P9) Minimum pressure (F_1) adjusting range Maximum pressure (F_2) adjusting range 120% 100% 100% 90% 10% 0% 0% 4 0 0 0 12 10 20mA 20mA 4 0 0 0 12 10 20mA 20mA 2.5 5V 2.5 5V 5 10V 5 10V (Note1) F_1 is adjustable in a range from 0% to 90% of the rated value. (Default value : 0%0.00MPa) (Note2) F_2 is adjustable in a range from 10 to 120% of the rated value.