Escapements Series MIW/MIS ø8, ø12, ø20, ø25, ø32 1 Do not use in an environment where vibration or impact occurs. Please contact SMC about use under such conditions because it can cause fracture or malfunction.
Do not allow hands or fingers near the cylinder during its operation. Your fingers may be caught between the body and the plate. If you need to come near the cylinder during its operation, install a cover on the cylinder. 4. Do not bring objects that are sensitive to magnetism near the cylinder. There is a magnetic built into the cylinder.
Therefore, do not adjust the stroke with the adjustment bolts or shock absorbers. 8. Do not use an air cylinder as an air-hydro cylinder. This will cause leakage of hydraulic fluid. 9. Adjust an auto switch's position so that it operates for movement to both the stroke end and backlash (2 mm) positions.
DO MY Bore size (mm) 22 22 30 30 45 45 60 CY DX DS DH Z DDH10 DC DT DU DR DO DL DE B DA DB Model 20 25 32 40 50 63 80 14 14 20 20 30 30 32 7 7 8 8 10 10 14 44 44 60 60 86 86 110 15 15 18 18 22 22 24 10 10 11.5 11.5 14 14 15 6.6 6.6 9 9 11 11 13.5 9 9 10.5 10.5 12.5 12.5 13 62 62 81 81 111 111 136 42 42 53 53 73 73 90 32 32 43 43 64 64 78 39 43 49 59 71 82 106 +0.058 0 +0.058 0 129 151 185
When raising the unit, do not insert your hands or fingers. As this is a heavyweight product, be sure to use caution. Screw holes for installing eyebolts are provided for 180, 200 and 250. (Eyebolts are not included in the unit.) Tie-rod nut, Spring washer Cylinder Tie-rod -X Wing nut Unit holding tie-rod 3.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the piston slider with air pressure) back to the proper position at the stroke end.
As an air slide table has magnets built-in, do not allow close contact with magnetic disks, magnetic cards or magnetic tapes. Data may be erased. 4. When mounting an air slide table, use screws with appropriate length and do not exceed the maximum tightening torque. Tightening with a torque above the limit could malfunction.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Normal Bottom Peak BATTERY 1.5V x 2 LR6 G kV MADE IN JAPAN IZD IZE POWER LIGHT 110 Do not apply a strong impact on the sensing part.
Do not use the product outdoors. 2. Do not place heavy objects on top of this product, or step on it. The external panel can be deformed and danger can result. Caution 1. Install on a rigid floor which can withstand this products weight. 2. When you remove casters to install the product, lift the product at least 10 mm by using adjuster-foot etc.
Do not use the back pressure regulator as shutoff valve or safety valve. 2.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) SW1 SW2 SW3 SW4 SW5 SW6 Node ID Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Socket connector pin layout 5 Green / Yellow: Not connected Specifications Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Yellow flashing Bus IN side: Link, Activity(10 Mbps) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
ON ON Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 1 2 3 4 5 6 7 8 Settings2 1 2 3 4 5 6 7 8 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
ON BUS OUT side: Link, No Activity 1 2 3 4 5 6 7 8 (Green) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. OFF. Parameter Setting Hardware Configuration I/O Map Diagnostic Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Refer to the valve catalogue for valve manifold dimensions. 1 ASInterface line (+) AS-i + 2 4 (0 V) RESERVE 2 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.