Fieldbus System Failure to do so may cause damage or malfunction.
YA 03 YA-03 YA-05 18 20 6.8 9 16 20 6 8 42 50 6.5 6.5 10 12 Applicable air cylinder bore Bore size (mm) 32, 40 50, 63 03 05 32, 40 50, 63 U V W Mass (g) Part No.
CLS YA YB YU Type A mounting bracket Type B mounting bracket Joint 32, 40 50, 63 80 100 YA-03 YA-05 YA-08 YA-10 56 67 83 100 18 22 28 36 6 8 10 12 55 100 195 340 CLQ MLGP Applicable mounting bracket Bore size (mm) Joint RLQ Type A mounting bracket Type B mounting bracket Type B Mounting Bracket 32, 40 YU-03 YA-03 YB-03 MLU 50, 63 YU-05 YA-05 YB-05 80 YU-08 YA-08 YB-08 ML1C 100 YU-10 YA-10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com YA 03 YA-03 YA-05 10 12 6.5 6.5 42 50 6 8 16 20 6.8 9 18 20 Applicable air cylinder bore Bore size (mm) 32, 40 50, 63 W V U Weight (g) Part No. 03 05 32, 40 50, 63 Mounting bracket YA-03 YA-05 55 100 56 67 18 22 6 8
Do not carry the servo motor by the cables, shaft or encoder. Do not hold the front cover to transport the driver. The driver may drop. Install the driver in a load-bearing place in accordance with the Instruction Manual. Do not climb or stand on servo equipment. Do not put heavy objects on equipment. The driver and servo motor must be installed in the specified direction.
Do not change this value by any means.
Do not drop or bump. When handling the switch, do not apply an excessive impact (1000 m/s2) by dropping or striking the switch. Even if the switch case itself does not become damaged, it could damage the internal switch and cause it to malfunction. 2. Hold the product from the body side when handling. To handle the product, hold it by its body.
Do not carry the servo motor by the cables, shaft or encoder. Do not hold the front cover to transport the driver. The driver may drop. Install the driver in a load-bearing place in accordance with the Instruction Manual. Do not climb or stand on servo equipment. Do not put heavy objects on equipment. The driver and servo motor must be installed in the specified direction.
Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 2. When operated at a very low flow rate, the series LV with flow rate adjustment may vibrate, etc. depending on the operating conditions.
Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications in the main section of the catalog. 4. Use a protective cover, etc., to shield valves from direct sunlight. 5.
Do not use a shock absorber together with air cushion.
When reassembling, do the opposite. How to Use Insert Plug When removing insert plug (1) from manifold base, push the lever area (2) of inset plug downward with thumb and pull it together with the lead wire (3) outward.
When reassembling, do the opposite.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could damage the groove.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion may result. This product is not explosion-protected. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result. Do not Do not cut off the power and compressed air supplied to this product while it is operating.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.