Table of Contents Do not put hands or fingers between the plate and body. Care should be taken that hands or fingers do not get caught in the space between the cylinder body and the plate when air pressure is applied. 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals may cause air leaks or faulty operation. 2.
Do not disassemble the product or make any modifications, including additional machining. 6. Do not use tools such as pliers to rotate the knob. AS-T It can cause idle rotation of the knob or damage. It may cause human injury and/or an accident. ASP 7. Verify the air flow direction. 4. The flow rate characteristics for each product are representative values.
Do not use the air cylinder as an air-hydro cylinder. This will cause an oil leak. 2. Install a rod boot without twisting. If the cylinder is installed with its bellows twisted, it could damage the bellows.
Failure to do so may cause damage or malfunction.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. LVA LVH LVD LVQ When the tubing is curved, straighten it out before using it. Maintenance The tubing may slip if there is oil or dust, etc., on the holder.
How to Order Manifold VV5Q 1 08 C6 1 N G Option Symbol Option Remains VQ1000 VQ2000 None Check valve for prevention of back press.
W1 B DX Z + Stroke DDH10 hole 90 B 4-DT B DS A DH DF DU DU DL DA 4-DR DO DO DC DE Rotating Angle Bore size (mm) 40 50 63 80 100 Bore size (mm) 40 50 63 80 100 Part no.
W1 B DX Z + Stroke DDH10 hole 90 B 4-DT B DS A DH DF DU DU DL DA 4-DR DO DO DC DE Rotating Angle Bore size (mm) 40 50 63 80 100 Bore size (mm) 40 50 63 80 100 Part no.
NO Do you have any problem, even if it might run over the target position? (Overrun) YES NO During the positioning operation, there may be the case it needs to do overruns or trials again. If there is any problem during the correcting motion, the products cannot be used.
/Cap (Resin part only) RBC C 08 Applicable model 08 10 14 20 27 RBC2015 RBC2725 RBC0805, 0806 RBC1006, 1007 RBC1411, 1412 Cap Cap cannot be mounted for basic type. Please place an order with cap type from the beginning.
NO YES Do you have any problem, even if it might run over the target position? (Overrun) NO Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? During the positioning operation, there may be the case it needs to do overruns or trials again.
When installing and removing an element, do not scratch or damage it by touching the corners of the case, etc. When washing the element, do not wipe it using a stiff brush or rag. Refer to page 529 for Microswitch for differential pressure indication switch. r Removing the element Rotate the air breather (cap) one-third of a turn counterclockwise and remove it.
Note) Do not change the rated voltage. VFS VS4 Series VFR2000 VQ7 Pilot valve assembly Tightening Torque for Mounting Bolt EVS Thread M3 (2 pcs.) M3 (3 pcs.) M3 (3 pcs.) M4 (4 pcs.)
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
Note 2) When using the D-M9lA, D-M9lAV or Y7BA, do not use the steel set screws which are included with the above auto switch mounting brackets (BA7-lll, BA4-lll).
Type A mounting bracket Type B mounting bracket 32, 40 YU-03 YA-03 YB-03 25 50, 63 YU-05 YA-05 YB-05 40 Material: Precision die-casting material equivalent to stainless steel 304 80 YU-08 YA-08 YB-08 90 Bore size (mm) O M J E D B Part no. 100 YU-10 YA-10 YB-10 160 K (Width across flats ) YB-03 32, 40 11.5 depth 7.5 34 9 25 7 12 H (With locking) YB-05 50, 63 14.5 depth 8.5 42 11 32 9 12 YB
Note 3) Specify the wiring specifications on the manifold specification sheet. 01 1 station Note) 08 16 8 stations (Double) 16 stations (Single) NKE Corp.: Uni-wire H System Note) Note) For details, refer to page 2-4-29.
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
Nylon tube Within 0.1mm Soft nylon tube Within 0.1mm Polyurethane tube Within+0.15mm, Within -0.2mm Do not use tube which do not meet these outside diameter tolerances.