Title not found P2, L5 X1 S/S . P3, L10 1 2 1 2 1/2 B Thd D A Thd C Hole Dia. Stainless Steel Threaded Parts Page & Part No. Line No. Page & Part No. Line No. D Line No.
Power off is displayed when power is not supplied. 3 Power status Indicates the connection status of the PCNFC reader / writer. 4 R/W connection status R/W undetected: NFC reader / writer is not identified or USB is not connected.
HOLD keykey SVON DRIVE RESET SETUP JOGJOG+ FLGTH MODE WRST Brake Origin SW: Origin switch Origin SW Limit SW-F: Limit switch F side Limit SW-F Limit SW-R: Limit switch R side EMS: Stop (Normal close) Limit SW-R EMS [ ] Stop Enable SW EMS [ ] Stop cancelled EMS 90 - (6-3-4) Output pin monitor It is possible to monitor the output pin of the controller with the pin number. (6-
How to Order IR 2 0 0 02 R 0 Pressure gauge mounting Precision regulator Body size R Note) Pressure gauge mounted on reverse side Type of setting Note) The standard mounting position of the pressure gauge is on the front, when viewing the regulator with the SUP side to the left and the OUT side to the right. 1 2 3 IR1000 IR2000 IR3000 Basic type (handle) Air operated type (series IR2000/3000
Model no. 1 3 5 A VZ X1 ( ) VZ3 A ( ) Manual override Entry is the same as standard products. Entry is the same as standard products.
86 FG S 1 A03T -V1 -X1 Type of seal Special Options R Rubber S Metal Standard X1 External Pilot Supply Size 6 Size 1 8 Size 2 10 Size 3 Pilot Exhaust Options Pilot Exh. through footprint V1 External Individual Pilot Exhaust Configuration FG 2-position Number of Solenoid Subplate (NPTF) FHG 3-position, Closed center FJG 3-position, Exhaust center Without Subplate A02T Side 1/4 For VSR/S8-6
Construction 1 4 1 4 1 3 1 6 6 2 5 5 7 Connection thread: G Connection thread: R,NPT Male connector Male elbow Swivel elbow No.
Body Size: 50, Thread: F (G), Port Size: 10 (1), Handle/Bonnet Material: B (Aluminum), Options: S (Built-in Silencer, EXH Port), Semi-Standard: R (Flow Direction: Right to Left), Made to Order: X1 (Body: Red)
Body Size: 50, Thread: G, Port Size: 1, Handle/Bonnet Material: Aluminum, Options: Built-in Silencer, EXH Port, Semi-Standard: Flow Direction: Right to Left, Made to Order: Body: Red
Body Size: 5, Thread: Rc, Port Size: 10 (1), Handle/Bonnet Material: A (Flame Resistant PBT), Options: None, Semi-Standard: R (Flow Direction: Right to Left), Made to Order: X1 (Body: Red)
Regulator Unit Combination: [Other FRL Combination Devices] Other FRL Combination Device, Port Size: Rc1, Compressed Air Quality: General Dry Air, Maximum Operating Pressure(MPa): 1, Case Material: [Resin] Polycarbonate Case, Case Guard: No, Exhaust Structure: Relief type, Flow Direction: [Reverse Flow (Right to Left)] Right to left, Drain Cock: [Not Provided] No, Pressure Gauge: -, Size
Body Size: 50, Thread: Rc, Port Size: 10 (1), Handle/Bonnet Material: A (Flame Resistant PBT)
Regulator Unit Combination: [Other FRL Combination Devices] Other FRL Combination Device, Port Size: Rc1, Compressed Air Quality: General Dry Air, Maximum Operating Pressure(MPa): 1, Case Material: [Resin] Polycarbonate Case, Case Guard: Presence, Exhaust Structure: Relief type, Flow Direction: [Standard Flow (Left to Right)] Left to right, Drain Cock: [Not Provided] No, Pressure Gauge: -
In this document TM and (R) are not specified. -EtherCAT is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. -83No.
Body Connection Thread Tightening Method Caution (1) Fittings with sealant: R, NPT 1) First, tighten the fitting by hand, then use a wrench appropriate for the hexagon flats of the body to tighten it a further two or three turns. For a tightening torque guide, see the table below. If the fitting is tightened with excessive torque, the fitting may break.
D E R S E R I E S ADH 4000 H E A V Y A U T O D R A I N S Y M B O L S ADH4 00 04 T H R E A D .Rc(PT) N .NPT M A X.
5 y q r !6 e !0 !3 w @1 @2 !5 t y q r e !0 !3w #0 @9 #3 @8 @7 o @0 !6 i !9 !8 u o @0 !7 i !9 !
(Except 50) MY1MW16/20/50/63 MY1CW16/20/50/63 L L L L L L R R R R R R R L L R R R L L L R Slide table operating direction MY1MW25/32/40 MY1CW25/32/40 L L This port is not available for use. (Except 32, 40) L L L L L L L L R R R R R R R R L L R R L L L R Slide table operating direction 8-12-3 4 Series MY1W Specific Product Precautions 2 Be sure to read before handling.
Single vane type Double vane type , , 0 -5 Chamfer 0 +4 0 9 a 0 a r r n n e n n g g g o o e e n i i 0 t t 1 a a 2 a 8 r t 1 t 7 +4 0 o o 0 0 n R R +4 0 +4 0 e o 0 i g t a 9 n t a o e r R g n n o a ti r a n t o o ti R a t o R Chamfer Chamfer Chamfer A port B port A port B port A port B port A port B port For size 40 actuators, a parallel keyway will be used instead of chamfer. +5 0 +
Applicable pad 04U/06U/08U Applicable pad 10U/16U Applicable pad 25U/32U Applicable pad 40U/50U 4.9 30 R 30 R R 25 30 R R R R 10.5 9.5 2 8 9 25 R 2 0.5 6 7 7 8 R R R R R R 45 45 45 2.7 1 R R 2.5 4.5 5 6.6 R 2.5 3.8 4.9 3.5 5 6 7.9 R 4.5 8 9 11.7 11.7 Note) R part has to be smooth with no corners.