Air Fittings Fitting Series For Special Environment

Male elbow: KRL Inch e l b a c i l p p A . D .

C95

When tightening the auto switch mounting screw, use a watchmakers screw driver with a handle diameter of about 5 to 6mm. Furthermore, use a tightening torque of 0.05 to 0.1 Nm. As a rule, it should be turned about 90 from the point at which tightening can be felt. Use a tightening torque of 1 to 1.2 Nm for the hexagon socket head set screws (M4 x 0.7). 1.

AS-FS Series Speed Controller with Indicator/ Elbow Type: Uni Thread Type

As a guide, tighten it by hand, then turn it two or three turns with a wrench. Check the dimensions of each product for the hexagon width across flats.

AS-FPQ/AS-FPG

D2 M1 L1 L2 T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max.

CP95

9 i *1 *1 C95K32 A A-A A !2 !1 @4 Component Parts Description Aluminum die-casted Aluminum die-casted Aluminum alloy Stainless steel Aluminum alloy Rolled steel Rolled steel Oil impregnated sintered alloy Steel Steel for spring Carbon Steel Steel Steel Material No. !4 !5 !6 !7 !8 !

CP95

9 i *1 *1 C95K32 A A-A A !2 !

AS-FPQ/AS-FPG

5 15-17-5 6 Series AS-FPQ/FPG Dimensions H (width across flats) Applicable tubing O.D. d A L4 D1 L3 D2 M1 L1 L2 T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max. Min. Max. 1 2 Min.

COMPACT COMPRESSOR, COMPACT COMPRESSOR, Q38, 3607.40000 lb

COMPACT COMPRESSOR, COMPACT COMPRESSOR, Q38, 3617.40000 lb

COMPACT COMPRESSOR, COMPACT COMPRESSOR, Q38, 3515.00000 lb

COMPACT COMPRESSOR. COMPACT COMPRESSOR. 3617.40000 lb. Q38.

COMPACT COMPRESSOR. COMPACT COMPRESSOR. 3588.00000 lb. Q38.

KA

(mm) A D2 L1 D1 M L2 Part No.

Antistatic One-touch Fittings Series KA

A D1 M L2 L1 D2 Part No.

AS-FPQ/AS-FPG

However, note that only the AS221FPQ uses steel. 713 AS-FPQ/FPG Series Dimensions H (Hexagon width across flats) Applicable tubing O.D. d A L4 D1 L3 D2 M1 L1 L2 T M5 type Applicable tubing O.D. d H (Hexagon width across flats) A L4 D1 L3 D2 M1 L1 T L2 Model Weight (g) (3) Tubing O.D. d T H D1 D2 L1 L2 L3 (4) M1 L4 (1) (4) Max. Min. Max. 1 2 Min.

AS-FPQ/AS-FPG

However, note that only the AS221FPQ uses steel. 713 AS-FPQ/FPG Series Dimensions H (Hexagon width across flats) Applicable tubing O.D. d A L4 D1 L3 D2 M1 L1 L2 T M5 type Applicable tubing O.D. d H (Hexagon width across flats) A L4 D1 L3 D2 M1 L1 T L2 Model Weight (g) (3) Tubing O.D. d T H D1 D2 L1 L2 L3 (4) M1 L4 (1) (4) Max. Min. Max. 1 2 Min.

Speed Controller with One-touch Fittings

Series Proper tightening torque (Nm) AS1002F-02 AS1002F AS2002F AS2052F AS3002F AS4002F 0.07 0.2 0.3 1 2 4 618 AS Series Speed Controller with One-touch Fittings In-line Type Dimensions L-bracket DIN rail mounting bracket Bracket on a single side Bracket on a single side AS-F AS-F L9 L16 L17 TMH L14 L15 ASD L12 L13 AS1002F AS2002F L22 L24 L23 AS L11 t1 2 x D6 t2 AS-FE 2 x D5 L19 KE AS-FG

ZSE3/ISE3

Detaching To detach a socket from connector, pull out lead wire while pressing the socket's hook with a stick having a thin tip (about. 1 mm). If the socket will be used again, first spread the hook outward. Pressure exceeding 0.5 MPa is being applied. (The pressure over rated pressure is being applied in case of positive pressure.) Reset the supply pressure less than 0.5 MPa.

Speed Controller with One-touch Fitting for Clean Room Series AS-FPQ/AS-FPG

D2 M1 L1 L2 T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max.

Flame Resistant (Equivalent to UL-94 Standard V-0) Speed Controller with One-touch Fittings Elbow Type AS Series

9 10 11 12 13 14 15 HNBR NBR NBR NBR NBR NBR Stainless steel, NBR Note 1) AS221F, AS321F: Electroless nickel plated. 605 AS Series Elbow Type H1 M5 type H1 (Hexagon width across flats) (Hexagon width H2 across flats) (Hexagon width across flats) H2 Applicable tubing O.D. d (Hexagon width across flats) Applicable tubing O.D. d A L4 L4 A L3 D1 D1 L3 M D2 L2 L1 M T D2 L2 L1 T Metric Size Min