IDU/IDF Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of auto drain will stop and water will flow out through the air outlet.) When tightening piping at the air inlet/outlet tube, the nozzle should be held firmly with a pipe wrench.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.
Wrapping of sealant tape When screwing together pipes and fittings, etc., be certain that chips from the pipe threads and sealant material do not get inside the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. Operating Environment Warning 1. Do not use in environments where there is a danger of corrosion.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Therefore, do not use it with or expose it to the following chemicals: paint thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, watersoluble cutting oil (alkalinic), etc. 2. Do not expose it to direct sunlight.
Do not use this product in a location where vibration is not allowed. 5. Actual speed of the product can be changed by load. When selecting a product, check the catalog for the instructions regarding selection. 6. Do not apply a load, impact or resistance in addition to a transferred load during returning to the original position.
For AC specifications, NIL is only set for electrical entry DO.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
Mounting direction is fixed, do not mount on opposite side.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3.
Do not cut the tube with pliers, nippers, scissors, etc.
In such cases, it is recommended to use a dual speed controller. 3) Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals etc. will result in leakage or malfunction. 4) Do not dent or scratch the mounting surface of the body and the plate.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble and modify. It may result in the trouble, malfunction, fire, etc. 2. Do not touch for a while when being energized or after cutting off the power source because it is high temperature. 3.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
Operating environment Do not use in operating conditions or environments where changes in color or deterioration of material due to corrosion occur. Do not use this product in a place where shock or vibrations occur. Do not use the hydraulic filter outdoors.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not use in direct sunlight. 5. When there are heat sources in the surrounding area, block off them. 6. Do not subject it to excessive vibration and/or impact. Please consult with SMC regarding use in this kind of environment, as this can cause damage and malfunction.
Do not ouch the electrode needle while energizing, or it may cause electric shock or accident. 3. Do not open the case to disassemble and reconstruct the product. It may cause electric shock, operation failure and disaster such as fire.