MLGP Do not drop or bump. Do not drop, bump or apply excessive impacts (300ms or more for reed switches and 1000ms or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. 6. Avoid incorrect wiring.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300ms or more for reed switches and 1000ms or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. 6. Avoid incorrect wiring.
Do not move the cover upward inadvertently during end plate installation.
Therefore, do not inadvertently move the setting of the guide adjustment unit. 2. Do not perform operation that results in negative pressure inside the cylinder. 2. Do not operate with the cushion needle completely closed.
Do not apply impact/collision/resistance for mover of actuator in operation. It will cause decrease of products life, damage to product, and so on. [Ground] Warning 1. Please do the earth construction surely. 2. Please refer to the driver manual for the grounding procedure and notes. [Unpackaging] Caution 1.
Warning If any error occurs, do not start operating the product.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Environment Warning 1.Do not expose the product to direct sunlight for an extended period of time. 2.Do not use in a place subject to heavy vibration and/or shock. 3.Do not mount the product in locations where it is exposed to radiant heat. 4.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not use compressed air containing chemicals, synthetic oils containing organic solvents, salt or corrosive gases, as this can cause damage or malfunction. 5. Do not use until you can verify that equipment can operate properly.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not use in direct sunlight. 8. Do not mount the product in locations where it is exposed to radiant heat. 9. Take appropriate measures against the lightning surge on the equipment side as the auto switches do not have any lightning surge resistance specified in the CE marking. Caution 1.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s or more for reed switches and 1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not use the product except for energy-saving control ejector Fire, malfunction, or damage to the product or the system can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not use the product except for energy-saving control ejector Fire, malfunction, or damage to the product or the system can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not use the product except for energy-saving control ejector Fire, malfunction, or damage to the product or the system can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not touch the LCD indicator. Do not touch the LCD indicator face of the pressure switch during operation. Static electricity can change the readout. 3. Pressure port Do not introduce wire, needles, or similar objects to the pressure port as this may damage the pressure sensor and cause malfunctions. 1. Do not use in an area where surges are generated.
Please do not over monitoring the cushion effect.