Compact Guide Cylinder Do not service or attempt to remove product and machinery/ equipment until safety is conrmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confrmed. 2.
Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals, etc. will result in leakage or malfunction. 4. Do not dent or scratch the mounting surface of a body and a plate. The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance. MGPW with Rubber Bumper 63 100 50 5.
Do not over tighten the lock nut.
CJ1 q Do not apply more than the allowable rotating torque to the piston rod. If more than the allowable rotating torque is applied, the non-rotating guide will be deformed and there will be a significant loss of rotational accuracy. This may cause damage to the machinery.
Polyurethane TU0425 2.5mm 4mm Metric size q Do not forcibly connect piping that could apply a lateral force to the cylinder tube, as this could cause the cylinder tube to tilt and lead to a malfunction.
To operate a relay as a load, use the relay shown in the table below or the equivalent, in order to extend the life of the switch. qWhen handling the product, do not drop an object on it, gouge it, or apply an excessive impact on it. wDo not operate it in an area in which a large amount of magnetism is present.
MX MXU Precautions on Handling Warning Mounting/Adjustment Caution MXS MXQ q Do not scratch or gouge the sliding portion of the guide rod by striking it with an object or getting an object trapped in it.
Contact Protection Boxes/CD-P11, CD-P12 Auto Switch Internal Circuits Reed switches
Free mount Speed controllers do not protrude from the top of the body. Top mount Bottom mount Side mount Wiring and piping direction can be selected depending on mounting conditions.
They do not guarantee an actual fixed range (expect approximately 30% dispersion).
There may be large variations depending on the surrounding environment (variations as much as 30%). 12 Compact Cylinder Series CQ2 Auto Switch Mounting Contact Protection Boxes/CD-P11, CD-P12 Auto Switches/Proper Mounting Position for Stroke End Detection D-Z7 and D-Z8 type switches do not have internal contact protection circuits.
B Z + Stroke DB DX DD 90 B 4DT A DS DH 4DR DB DU DO DO DC DE DU DL Rotation (mm) No.
(between lead wire and case) Withstand voltage Ambient temperature 10 to 60C Enclosure IEC529 standard IP67, JISC0920 watertight construction Contact Protection Boxes/CD-P11, CD-P12 Lead Wire Length
(Do not tighten with pliers.) @silrc I SERIES NCDJ2 Connection examples to relay and solenoid valve Basic wiring 3 wire system (When power source for switch and load is common) Rd lead wi: Connect io the power sourc e (powet source lerminal) lo operare main circuit of switch.
I installed \tl .1 onry) f e lri=d.c-) L Type of actuation With irdicator ght and surge v0rrage suppress0r 1 INormal closed 2 lNormal open S and Z not available lor grornmel. i 1 oVAC type inc udes S (do not specity). Body Port size ut subplate _,,' (a --1ry1 wv : Standard typerindividual gilot exhaust l--l l ?
(lf lubrication is used, do not discontinue its us.) Olf the kinetic energy oI the load exceeds the permissible range, use external stops to absorb load. O Connect piping atter thoroughly flushing it. O Do not use trydraulic fluid. @Shaft Load lf a static (i.e. non-dynamic) load only is applied to the actuatot it is possible io apply the load values shown in the table below.
DO Without air cushion (mm) Bore size (mm) Part No.
Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Caution Do not uninstall, with the power supply connected to the controller.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.