CNS 11 10 Since this is a guideline including hysteresis, not meant to be guaranteed.
Please note that if the forced mode is canceled while PROFINET communication with the PLC is established, the input / output data with the PLC will be shown immediately. -90No.EX-OMY0027 (11) To change the Password, log in using Administrator mode and select CHANGE PASSWORD.
EX500-DX B Install the product using 2 M5 screws x 20 mm minimum with a head 9 to 11. NOTE Refer to the product catalog or SMC website (URL http://www.smcworld.com) to obtain more detailed information about product specifications. 1 3 5 7 9 11 13 15 The direct current power supply to combine should be UL1310 Class 2 power supply when conformity to UL is necessary.
No.PF-OMP0002-H PRODUCT NAME Digital Flow Switch MODEL / Series / Product Number PFMB7501 PFMB7102 PFMB7202 Contents Safety Instructions 2 Model Indication and How to Order 10 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 14 Installation 14 Piping 16 Wiring 17 Outline of Settings [Measurement mode] 21 Flow Setting (set value only) of OUT1 OUT2 [3 step
(hysteresis or window comparator mode). -44No.PF-OMW0004-B Model PF3W704 PF3W720 PF3W740 2-screen display (main screen, sub screen) Main screen: 4-digit, 7-segment, 2-colour; red/green Sub screen: 9-digit, 11-segment (5th digit is 7-segment only), White Display method Display updating frequency 5 times/sec.
If the minimum setting unit is 1 L/min, the display will change in 1 L/min steps, e.g. 10..11..12 L/min. M Minimum setting unit O Operating fluid temperature Range of fluid temperature that can be used by the product.
IZN10 IZN10 IZN10 IZN10 01 01 01 01 P P P P 06 06 06 06 Z Z Z Z B1 B1 B1 B1 IZN10 AC 01 02 11 Rc1/8 NPN P PNP 06 6 07 6.351/4) 16 6 ( 17 6.351/4() (3m) Z (10m) N IZN10-NT L DIN IZN10A002 IZN10B1 L B2 B3 DIN 01 06 ES 2 01 ES 17mm 2 2 02 3 3 11 Rc1/8 4 4 /IZS30 /IZS30 /IZS30 /IZS30-M2 M2 M2 M2 06 6: 07 6.351/4: 16 6 :( 17 6.35(1/4):() IZN10-CP(3m) IZN10-CPZ(10m) IZN10A003 NPN
Detection range.11 6-3. Cautions on installation .11 6-4. Timing chart .12 7. Exterior dimensions.12 1 1. Safety Instruction These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard by labeling "Caution", "Warning", and "Danger".
Take measures to ensure that water droplets from condensation are not splashed onto any electric parts or equipment. 11. Condensation and freezing of the directional control valve Condensation and freezing may occur in the directional control valve due to the same cause as 10. Condensation and freezing of the pilot port.
Take measures to ensure that water droplets from condensation are not splashed onto any electric parts or equipment. 11. Condensation and freezing of the directional control valve Condensation and freezing may occur in the directional control valve due to the same cause as 10. Condensation and freezing of the pilot port.
ON/OFF signal Ball valve Pressure regulator PB1313A Filter FLUID OUT Air supply source FLUID IN Solenoid Meter-out valve Circuit example 11 7.
Fig. 9 Normal output OFFt0 Fig. 10 Sequence OFF0 Fig. 11 Sequence 6. Cascade connection There are only outputs up to 10 points (6 points in the case of VXFC06A) on a single board. However, it is possible to increase the output points by cascading (multiple board connection).
Fig. 9 Normal output OFFt0 Fig. 10 Sequence OFF0 Fig. 11 Sequence 6. Cascade connection There are only outputs up to 10 points (6 points in the case of VXFC06A) on a single board. However, it is possible to increase the output points by cascading (multiple board connection).
Output indication mode [Output Ratio] Setting range : -100 to 100% Min. increment : 1% Indicated content: Thermo module output ratio (Ex.: -73%) Function: Indicates Thermo module output ratio with O u t p u t R a t i o M O D E < 7 3 % increment of 1%. + is not indicated but + means heating and means cooling. 11.Upper/Lower Temp.
(Take care not to scratch the O ring groove. > Step 3 O-ring Installation surface of the O-ring Body Remove the outer seal O-ring from the Body (Take care to prevent the mounting surface of O ring from being damaged ) 11 XL-OMO0001-A 6-3. Assembly Procedure Step 1 Step 2 O ring groove Clean cloth Valve Ethanol Assemble parts eliminating any dust or debris.
(See page 11) Caution 3. Flushing Flush piping line with air before the first usage. 1. Replace deteriorated or swollen O-ring. Replace O-ring one year after starting use, or if fluid leakage occurs. (See page 7 Table 1: O-ring for replacement) 4. Prepare air discharge circuit where necessary. 5. For high temp. type, protection against burning shall be prepared. 2.
Specifications 1 11 / 17 FGX-OM-F001-A 3. Specifications Table3-1 Specifications Item Specifications Fluid Hydraulic fluid: Oils below are applicable.
For detailed description of the signals, refer to the following pages. 15 (2) Internal circuit (Numbers in brackets indicates the pin numbers) (5) PWR_DC24V LF (6) PWR_GND Output signal GND (9) CTR (10) CYL (11) VAL (16) RF (17) PWR Max.
AF AR 4 - 1) 5 2) 3) 5 4) 1 ISO VG-32 2-2. 1) 2) 3) 4) 5) 6 7) 5 - 8 9) , 10) 11) 3 1) P10 [2-6.] 2) 3) 4) 5) 6) 7) (40) 6 - 2-3. 1) 1 P10 [2-6.] fR Ft N () mm 1. (MPa)=(MPa)+{(kg) 2)} X /(mm ,, 2) 3) 4) 7 - 5) 6) 7) 8) 9) 24. 1) 2) 3) 8 - 1) 2) 1.52 2 2. 2-5. ,AS 9 - 2-6. P7.1. 1.
PTFE X446 GR-F-005(5g) 1) 25 2) () 5. 11. 26 6. 12. 27 Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2012 SMC Corporation All Rights Reserved