Compact Low Friction Cylinder Compact Low Friction Cylinder Compact Low Friction Cylinder Compact Low Friction Cylinder Metal Seal Type Metal Seal Type Metal Seal Type Metal Seal Type MQ MQ MQ MQ Series Series Series Series (M Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3. Do not service or attempt to remove product and machinery/equipment until safety is 3.
However, components that are combined together during the distribution process do not have a label on them. 4.
Do not bring into close contact with objects which would be influenced by a magnetic field. As an air slide table has magnets builtin, do not allow close contact with magnetic disks, magnetic cards or magnetic tapes. Data may be erased. 3. Do not apply strong impacts or excessive moment when mounting workpieces.
Do not expose it to direct sunlight.
Do not expose the product to direct sunlight for an extended period of time. 3. Do not use in a place subject to heavy vibrations and/or shocks. 4. Do not mount the product in locations where it is exposed to radiant heat.
Do not use tools on the pressure regulator knob as this may cause damage.
Model (Made to Order) PPA Pressure range Note) Connection thread (MPa) Indication unit Model AL MPa 0 to 1.0 M5 (Female thread) G27-10-M5-X201 Note) Do not apply more excessive pressure than max. pressure display. It will be a cause of malfunction.
The switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 2. Mount switches in locations where there is no vibration greater than 98 m/s2, or impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
Do not wire in conjunction with power lines or high voltage lines. Wire separately from power lines and high voltage lines, and avoiding wiring in the same conduit with these lines. Control circuits including switches may malfunction due to noise from these lines. 5. Do not allow a load to short circuit.
Do not use the materials for buffer face which might cause to spark by collision. Load Warning Allowable eccentric angle 1 < 5 1.
The graphs do not show the loadable mass. Refer to the Model Selection for the loadable mass.
Do not apply external force to the coil. Apply a wrench to the exterior surface of the piping joint at the time of tightening. 3. Do not use heat insulators, etc. to keep the temperature at the coil assembly. Do not use a tape heater for freeze prevention except on the piping and body. If may cause the coil to burn. 1.
Do not poke the inside of the piping port with a stick. The rectifier could break, making the product unable to sustain the desired performance. 4. Do not touch terminals or connectors when energizing the product. It could cause electric shock, malfunction, or damage to the switch.
Do not use a lead wire longer than 30 m. Wire the DC (-) line (blue) as close as possible to the power supply. Operating environment Do not use the product in an environment where the product is constantly exposed to water or oil splashes. Otherwise it can cause failure or malfunction. Take measures such as using a cover.
As the connected actuator will start confirm that it is safe to do beforehand.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use the materials for buffer face which might cause to spark by collision. Load Warning Allowable eccentric angle 1 < 5 1.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not use the product in an environment where corrosive gases or fluids can be splashed. Otherwise damage to the SI can result, causing malfunction. Do not use the product in an area where surges are generated.
Do not use until you verify that the equipment can operate properly. After mounting, repair or modification, etc., connect the air supply and electric power, and then confirm proper mounting by means of appropriate function and leak inspections. Do not let chips or extraneous material enter inside the cylinder from the inlet.