ø 40, ø 50, ø 63, ø 80, ø 100 Series CLA2 Fine Lock Cylinder Double Acting, Single Rod Note 2) When using the D-M9lA, D-M9lAV or Y7BA, do not use the steel set screws which are included with the above auto switch mounting brackets (BA7-lll, BA4-lll).
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the piston slider with air pressure) back to the proper position at the stroke end. 3. Do not apply a lateral load to the external slider.
W1 B DX Z + Stroke DDH10 hole 90 B 4-DT B DS A DH DF DU DU DL DA 4-DR DO DO DC DE Rotating Angle Bore size (mm) 40 50 63 80 100 Bore size (mm) 40 50 63 80 100 Part no.
Piping Caution Caution Handling 1.Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2.Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
The set screws in the figure below are for securing the guide shaft, so do not loosen them except for the purposes of replacing the seals. This can cause a malfunction. Caution 1. Do not use the cylinder in an environment where the cylinder is expose to moisture, adhesive foreign matter, dust or liquid such as water or cutting fluid.
A B High precision type Basic type Port location Nil E Side ported Front ported Size 1 2 3 7 A With adjustment bolt Dimensions Clean series products do not have a hollow axis.
Do not install it by directly grasping the piston rod with a pair of electricians pliers.
W1 B DX Z + Stroke DDH10 hole 90 B 4-DT B DS A DH DF DU DU DL DA 4-DR DO DO DC DE Rotating Angle Bore size (mm) 40 50 63 80 100 Bore size (mm) 40 50 63 80 100 Part no.
When installing the cylinder into equipment or performing adjustments, etc., be sure to apply air pressure of 0.25 MPa or more to the unlocking port, and do not perform work using the unlocking cam. 3.
Do not operate the CS1 series at twice the output. Applicable Series Series Description Note Vol. no.
Prevention of electric shocks and fire Do not operate the switch with wet hands. Also, do not operate the thermo-con when water is present on its exterior surface. 2. Action in the case of error If any error such as an abnormal sound, smoke, or bad odor occurs, cut off the power at once, and stop supplying and conveying fluid.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of the auto drain will stop water vapor from discharging through the air outlet.) If it is unavoidable that the tube goes upwards, make sure it only goes as far as the position of the auto drain. Power Supply Caution Connect the power supply to the terminal block.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (The auto drain will not be activated and water will try to escape via the air outlet.) If it is necessary that the tube goes upwards, make sure it only goes as far as the position of the auto drain.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 3 Branch port (COM A to D) 4 Branch port A (COM A) 128 inputs/128 outputs Number of points Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
IO-Link DI DO StandardIO StandardIO 2 0x00 . 9-4 X0 X1 X2 X3 IO-Link 1 2 3 4 IO-Link 2 (I/Q) Bit 1 Bit 3 Bit 5 Bit 7 EX245-LA1 (EX245-LB1 0) 4 (C/Q) Bit 0 Bit 2 Bit 4 Bit 6 DO 2 4 (C/Q) Bit 0 Bit 2 Bit 4 Bit 6 DI() 9.5.
Refer to the SMC website (URL http://www.smcworld.com) to obtain more detailed information about troubleshooting. 3 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Branch port (COM A to D) 8 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
An injury or failure can result. 3 Display LED LED display to indicate the input unit status. 128 inputs/128 outputs Number of points Sensor connector Connector for sensor. 4 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. No.
List of output mode Do not operate the product outside of the specifications. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Panel Measurement mode Hysteresis mode Mounting screws Press the button for 2 s or longer Switch output Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
Do not disassemble, modify (including change of printed circuit board) or repair. An injury or failure can result. 1 s. after This function is to display error location and content when a problem or an error occurs. All indications Instantaneous value indicatio Error Name Error Display Error Type Troubleshooting Method Do not operate outside of the specification.