LEH_C 2) 3) 4) P.40 7.1 9 - 6. !
Model Selection Based on Exhaust Flow Rate The exhaust flow rate that is calculated in step 1. Calculation of Exhaust Flow Rate is the flow capacity shown in Graph 2. Select the model that is shown with a point where the dotted line, for flow capacity, and the solid line, for flow rate characteristics, intersects.
X1 3-port specification [2(B) port plug] The 3-port specification is a specification with the 2(B) port plugged and closed. The 3(EB) port should be kept open for pilot exhaust.
Communicated at 100 Mbps 1 1 Communicated at half duplex 1 0 1 Communication method 1 White/Orange 2 Orange 3 White/Green 4 5 6 Green 7 8 1 2 3 4 +Tx +Rx -Tx -Rx Communicated at full duplex 1 1 2 1 2 3 1 2 4 SW1 CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: 5 Cable color: Signal name Pin No.
RUN1 input circuit at external input operation v Note) : This circuit is not necessary for READY signal. Controller (VYU5-D) External appearance of exclusive controller RUN1 STOP START SEL. SW RESET RUN2 RUN1 OV INPUT 6 7 5 8 4 + 9 3 SET UP A 2 B 1 0 C D 1 E F 0 to 10V V R 1 OUTPUT SET UP BALANCE CONTROLLER VYU5-D 2 V R 2 OV ERR.
Note 1) The longer the tubing of the cylinder, SSC valve, and speed controller, the longer is the delay during actuation. Note 2) If a load is applied constantly, such as when the cylinder is mounted vertically, it is not possible to control the speed of the stroke in the same direction as that of the load.
In addition, changes in the force on the cylinder parts may cause dangerous movement to occur with forceful impact. 120 mm or less 2. Affix a protective cover in places where there is a danger of personal injury. A large gripping force is generated during clamping. If there is a possible pinching hazard, design the structure to avoid contact with the human body. 3.
In principle, this function counts each time there is a rise or fall in either of the A or B phase pulses. 2 1 Amplification/ Interpolation circuit Counter A phase B phase Magnetic resistance element Piston rod Magnet Count 1 2 3 4 5 6 7 8 9 10 .
Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction. 2) Vacuum pads are excluded from this 1 year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
fitting 1(P): Male thread 2(A): One-touch fitting 1(P): One-touch fitting 2(A): Male thread 1(P): Male thread 2(A): Male thread 2(A) 2(A) 2(A) 2(A) Applicable tubing O.D.
Installation Operator Panel mounting Fix the panel mount adapter to the product with the mounting screws (nominal size: 3 x 8 L, 2 pcs.) supplied. The monitor can be mounted on a panel with a thickness of 0.5 to 6.0 mm. 2. Press the or button to change the set value. The button is to increase and the button is to decrease the set value.
Grease used The special grease is used for the guide and the ball screw. Please confirm it to our company when you maintain the grease up etc.. 2 Recommended tube diameter Table2Recommended tube diameter An enough fluence is not obtained by a diameter that is thinner than this. Moreover, please enlarge it by one size when the piping length exceeds 3m.
* 9 : 025 --l ,eln the machjne lype seleclion whn I dimsnsion becoms longer, selct the cylinclr hsvins a suflicient i. 020 \ Not t) when the cylinder i to be used ae a stopper use is at 30 stroke or les. Note 2) MGOL (Ball bush bea/ng) cannot be used as C16 012 \ \ '**;;.
Note 2) A current of more than 80 mA is flowing to OUT2. Check the load and the wiring for OUT2. Note 1) The set data has changed for some reason. Perform the RESET operation, and reset all the data again. Note 2) Note 1) The flow rate is over the flow rate measurement range. Use an adjustment valve, etc. to reduce the flow rate until it is within the flow rate range.
Specification NOTE The direct current power supply to be used should be UL approved as follows : Circuit (of class 2) which is of maximum 30Vrms (42.4V peak) or less, with UL 1310 class 2 power supply unit or UL 1585 class 2 transformer. The Pressure switch is a approved product only if it has a mark on the body.
Connection is complete when the knurled part is fully tightened. Check that the connection is not loose.
OFF 2 RD+ Receive Data + Operating normally 1 3 3 TDTransmit Data SI unit-related diagnostic error is detected. (load power for the valve is not supplied or outside tolerance range) The configuration information registered in the master and the number of output points does not match (BF flashing). RDReceive Data 4 SF 2 Red ON BUS IN: M12 4-pin socket D-coded (SPEEDCON) 1 OFF No.
Use VHK2 (2 port valve) for vacuum application. JIS Symbol 2 port valve 3 port valve Construction 2 port valve/Series VHK2 3 port valve/Series VHK3 The valve direction clearly indicates whether the valve is open or closed.
Note 2) (Nominal size) is not needed as the part number starting with the AL-H is a dedicated number. Note 3) The material of seals (AL-128H-V to AL-137H-V) is EPDM-70. 503 A FH99 Series Replacement parts Handling Precautions Description Part no. Applicable model Connection side: IN Connection side: OUT Set contents q Mounting Confirm IN and OUT before connecting.