Mechanically Jointed Rodless Cylinder with Brake, Hy-rodless Cylinder Series ML1C ø25, ø32, ø40 1 The most suitable piping position can be selected by choosing each 1 port from A, B, C and combining them.
The most suitable piping position can be selected by choosing each 1 port from A, B, C and combining them.
8370: JIS B 8361: JIS B 9960-1: -1 ) JIS B 8433: *2) 1. 2. 3. 1. 2. 3. 4
Due to meter-in control, the cylinder moves from A to B regardless of whether it is an initial operation or a normal operation. When it reaches B, the head pressure (PH) rises quickly as indicated by the line from C to D.
' sering.rylq, . _'_" h'rCl" 9boke -l-qvartr b?
' sering.rylq, . _'_" h'rCl" 9boke -l-qvartr b?
A B C E Applicable clip Clip for P7 Clip for P10 Conforms to JIS B 2401 dimensional standard for O-rings for industrial applications.
(B contact) 3 wire GXL-N12FTB Switch specifications (SUNX Corporation) GXL-N12FT(B) Part no.
Weight g 65 65 25 15 15 B side traveling parallelism to A side Refer to Graph 1.
B is applied to approx 180cm3-capacity actuator. Note 4) Standard lever is not attached. Note 5) It is to be used together with A or B when tending to overshoot by the use of A or B. It is mounted to the body as a replacement of the standard compensation spring. Note 6) With terminal box, Non-explosion proof. Select 1 for the construction.
(B)). Fig. (A) When air is supplied to the exhausted cylinder, the air causes the check valve to close. Also, because the piston valve is fully closed due to the cylinder's low internal pressure, air is supplied gradually via the throttle of the set needle. Therefore, the cylinder operates slowly under meter-in control. Fig. (B) Fig.
These grcoves can b used for fnmly fixing the tying ba.ds or lad wis oi the auto switch, etc., dd also termiml boards, etc-, to the main body of the cylinder q " l-f9 -l lF'rg _1+T l---' l I I Detailed drawing ol part a Detailed drawing of part b Part a Patl a Ff"frf?
D E L 4-H Valve mounting hole F Bracket Mounting Dimensions/Bracket Material: Stainless Steel (mm) A B C D E F G H J L Valve model Bracket part no.
bracket) are included with the above parts. 3 Direct Operated 2 Port for Heated Water Series VCB Dimensions Grommet: G Conduit: C Q Approx. 300 F D Approx. 280 D Q F C G1/2 C R R E E B A H 2-P Port size 2-P A 2-M Thread depth N B H Port size 2-M Thread depth N L L K K Conduit terminal: T F (Q) 34 25 U R C G1/2 E B A H D 2-P Port size (S) 2-M Thread depth N L K (mm) Electrical entry P Port
These grcoves can b used for fnmly fixing the tying ba.ds or lad wis oi the auto switch, etc., dd also termiml boards, etc-, to the main body of the cylinder q " l-f9 -l lF'rg _1+T l---' l I I Detailed drawing ol part a Detailed drawing of part b Part a Patl a Ff"frf?
B Contact output signal 3 selected alarm Sets the alarm selected for the contact output signal 3.
A B 18 - 43 Timing diagram (Example) The figure shows the timing diagram of operation for the selected step data input type and the PLC parallel input/ output signals used when power is supplied.
(b) Moisture in the refrigerant circuit (colour of the indicator) Green (DRY) ---Good Yellow (WET) ---Moisture is present in the refrigerant.
2 M4 x 0.7 x 8 Nickel plated JIS B 2805 Nominal 6 Chromated Cross-recessed head cap screw E type snap ring Handle Ring Lock nut Needle O-ring Chromated Chromated JIS B 2401 P12 Replacement Parts No. Description Material Parts no. Valve Spring Seal NBR, Stainless steel o !0 !
Model: 10 (Side Ported), Number of Cores - Lead Wires: L2 (17 Cores), Lead Wire Length: 2 (1.5m), Valve Stations: 8 Stations, P, E Port Locations: B (Both Sides), SUP/EXH Block: R (External Pilot), A, B Port Size: C6 (ø6 One-touch Fitting), Mounting: B (DIN Rail Mounting, Name Plate w/o Station Number)