3 Port Direct Operated Solenoid Valve Metal Seal, Body Ported/Base Mounted 1

(Values at the initial period) VQZ VZ VS VFN Base mounted Flow Characteristics/Weight Weight (kg) Flow characteristics P A Port size Rc C [dm 3/(sbar)] b Cv C [dm 3/(sbar)] b Cv A E AC 0.34 0.34 0.40 0.40 0.32 Body type Valve model DC 0.46 0.46 0.52 0.52 0.44 VS3115-01 VS3115-02 VS3110-02 VS3110-03 VS3114-00 1 8 1 4 1 4 3 8 2.5 3.6 3.2 3.6 0.39 0.34 0.31 0.18 0.86 0.86 0.93 0.94 0.66 0.88

Pressure Relief 3 Port Valve with Locking Holes

Implement suitable protective measures in locations where there is contact with water droplets, oil, or welding spatter. 7. Install a silencer into exhaust port to prevent the dust ingress if there is a lot of dust in atmosphere, as dust may cause air leakage. Maintenance Warning 1.

Thermo-chiller

16 130 16 180 16 Maximum pump head [m] 50 49 55 49 68 49 Settable pressure range5 [MPa] 0.10 to 0.50 0.10 to 0.49 0.10 to 0.55 0.10 to 0.49 0.10 to 0.68 0.10 to 0.49 Minimum operating ow rate6 [L/min] 20 2 25 2 40 2 Tank capacity [L] 42 7 42 7 60 7 Bypass circuit (With valve) Installed Electric conductivity setting range [S/cm] 0.5 to 45.0 0.5 to 45.0 0.5 to 45.0 Circulating uid system

ZSE30/ISE30

Do not exceed the screw-in torque of 7 to 9 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. Do not use pressure sensors with corrosive and/or flammable gases or liquids. 5. Allow a sufficient margin of tube length in piping in order to prevent application of torsional, tensile or moment load to the tubes and fittings. 6.

VND

Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Bracket (Option) 2-M4 x 0.7 depth 7 Main port Rc Model VND10D-6A VND10D-8A VND10D-10A 1 8 1 4 3 8 Port size 10A, 15A, 20A, 25A G (Valve open) Pilot port Indicator (Option) (Back side P2) Bracket (Option) Main port Main port Rc A B C D E F G M N P Q R S T U Model 3 8 1 2 3 4 1

MGC

7 !8 !9 @0 @1 @2 Material Aluminum alloy Aluminum alloy Aluminum alloy Carbon steel Note Clear hard anodized Clear hard anodized Chromated No.

Clean One-touch Fittings For Driving Air Piping KPQ/KPG Series

Connection thread size Proper tightening torque (Nm) M R 1/8 7 to 9 R 1/4 12 to 14 H/DL L/LL R 3/8 22 to 24 R 1/2 28 to 30 KC Installation of Threads 3. Tightening tools Tighten with an appropriate wrench using the hexagon wrench flats on the body. Position the wrench on the base as close as possible to the threads.

Air Cylinder/End Lock Series MBB ø32, ø40, ø50, ø63, ø80, ø100

7 !8 @1 @6 14A !9 @0 CJ1 CJP @7 i o CJ2 80, 100 CM2 C85 !0 !1 CG1 @2@3@4@5 14B MB Locking at rod end C95 CA1 CS1 Manual release non-locking style: L Material Note Component Parts Material Note Component Parts No. q w e r t y No. !7 !8 !

Direct Operated Solenoid Valve Metal Seal Series VS4
10 1

Class B or equivalent (130C) Note) Coil insulation type Note) Based on JIS C 4003 How to Order 1 L 02 0 1 1 4 VS C Thread type Direct operated/Metal seal solenoid valve Electrical entry Nil Rc NPT NPTF Option 4, 5 port valve N Symbol Electrical entry Electrical entry position C T U D T Sub-plate Conduit Type of actuation Conduit with terminal Sub-plate Body size: 1/8 standard F Single

PSE540/560

ZS-28-C 1 pc. Connector for PSE300 PF2 Specifications IF Conforms to CE marking and UL (CSA) standards.

Guide Table Series MGF ø40, ø63, ø100 1

3 Hard anodized Nickel plated Tube Hexagon socket head cap screw C Carbon steel Aluminum alloy w !4 20Clear anodized Rod cover Magnet Magnetic material Aluminum alloy e !5 Chromated Piston Plug Carbon steel Aluminum alloy r !6 Data Electroless nickel plated Piston rod Element Resin Carbon steel t !7 Anodized Plate Snap ring Spring steel Aluminum alloy y !

MGP-OM0242Q

Precoutions on Selection 7 7. Precautions on Design 7 8. Mounting Methods 8 9. Piping 11 10. Operating Environment 12 11. Speed Control 12 12. Clean Series / Precautions 13 13. Troubleshooting 17 14. Auto Switch 18 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

Trimmer Auto Switch Series D-
7K/D-R
K

Applicable actuator and operation range (angle) Sensor unit D-Y7K Air gripper (mm or ) Model Bore size (mm) 10 4 12 16 20 25 32 40 50 63 80 100 MHZ2 MHL2 MHS2 (2 finger) MHS3 (3 finger) MHS4 (4 finger) MHC2 MHW2 Parallel gripper 7 8 8.5 7 5 Wide opening 6.8 10.5 11 12.5 8.5 8 Parallel gripper 6.5 7 7.5 8.5 Parallel gripper 6.5 7 7.5 8 Parallel gripper 6.5 7 7.5 8.5 30 to 10 30 to

ZK2-C

ON ON A (/) 1 OFF OFF DC(+)DC(-) 2 ON DC(+)DC(-) NPN PNP () 3 OFF ( ) () DC(+) DC(-) () 4 () 5 -47NO.ZK2-OM00801-B No. 80 mA (Er1,2) () ( (Er1,2) ) (Er0,4,6,7,8,9) DC24 DC24 V10% (Er0 4 6 7 8 V10% 9) 6 "HHH" (HHH) "LLL" (Er3) (LLL) (Er3) 3.5 F.S. DC24 V10% DC24 V10% DC(+) DC(-) 7 -48NO.ZK2-OM00801-B No.

Ｍ agnet Gripper Unit for Collaborative Robots

Specifications .7 3-3. Gripping force .8 3-4. Dimensions .10 3-5. Connector and pin layout . 11 3-6. Center of gravity . 11 4.Product Specifications .13 4-1. Magnet gripper .13 4-2. 3-port solenoid valve .14 4-3. Auto switch .15 5.Operating method or operation .16 5-1Precautions for Design .16 5-2. Installation .17 5-3. U R C a p .20 5-4. Air supply .26 5-5. Piping .26 5-6.

ZSP1

ZS-10-5 A-50 1 pc. 0.6 m 30 3 m 50 5 m Specifications Model ZSP1-B ZSP1-S Fluid Air Operating pressure range 20 to 101 kPa Applicable adsorption nozzle dia. 0.3 to 0.7 (Refer to Graph (1) on page 16-7-3.) 0.5 to 1.2 (Refer to Graph (2) on page 16-7-3.)

Series CDU 10-/11- 21-/22- ø6, ø10, ø16, ø20, ø25 Free Mount Cylinder

Fittings & Tubing Air Cylinders Rotary Actuators Relief port 2 x M5 x 0.8 2 x P through M5 x 0.8 R GC GB E GA MM D C J 2.8 2 x P through A 4 x T counterbore E 0.5 B H S Z (mm) 6 depth 4.8 5 S 10 15 20 25 30 5 Z 10 15 20 25 30 Bore size B C D E GA GB GC H J MM P R T A 13 22 3 23 16 15 13 10 3.2 7 M3 x 0.5 31 10 7 6 10 15 24 4 24 33.5 16 15.5 16 11 M4 x 0.7 3.2 9 6 depth 5 64 69 74 79 84 89

PSE200.eng

When setting, allow 7 digits or more between P1 and P2 (and P3 and P4). Less than 7 digits will not allow correct operation. This operation manual is intended for those who have knowledge of machinery using pneumatic equipment, and have sufficient knowledge of assembly, operation and maintenace of such equipment.

3 Port Air Operated Valve Series SYJA300 1

N.O. 0.4 0.3 0.2 0.1 0.2 0.3 0.4 0.5 0.6 Operating pressure (MPa) Flow Characteristics/Weight C [dm 3/(s bar)] b Cv C [dm 3/(s bar)] b Cv 1 2 (P A) 2 3 (A R) Valve model Flow characteristics Weight (g) Effective area (mm2) Pilot port size Type of actuation Port size SYJA312-M3 SYJA322-M3 SYJA314-M5 0.41 0.18 0.086 0.35 0.33 0.086 Body ported N.C. N.O. N.C.

EX600-SEN_eng

(Default setting) Number of occupied valve 8 outputs Number of occupied valve 16 outputs Number of occupied valve 24 outputs Number of occupied valve 32 outputs Mode OFF OFF OFF ON ON ON 1 2 3 4 5 6 7 8 ON 2 1 0 1 ON/OFF : : Mark C on the unit Mark B at cable end Mark A at cable end OFF OFF ON (1) Input data + System diagnosis + Unit diagnosis (up to 10 units) Input data + System diagnosis