CM2 Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fitting into the port, it is likely to damage the junction part with cover. 2.Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged.
Use clean ai Do not use compressed air that contains chemicals, synthetic oils that include organic solvents, salt, corrosive gases, etc., as it can cause damage or malfunction. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3.
Sensuous phenomenon nothing to do with function.
B Supply pressure and the Stopper screw (Do not move) OUT1 output are connected by rotating the Auto/Manual changeover screw towards M.
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 1. Drain flushing Remove drainage from the air filters regularly. 2. Lubrication Once lubrication has been started, it must be continued.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. Do not use the components other than the specified components. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
If they do not match, stress could be applied to the rod and the cylinder tube, causing wear to the inner surface of the cylinder tube, the bushing, the rod surface, and the seals may become damaged. 3) When mounting the cylinder, do not apply a lateral load to the rod.
For materials of the flow control equipment, refer (2) When there is a large amount of to their construction drawings. condensate (2) Do not expose the product to direct sunlight Compressed air containing a large amount of for an extended period of time. condensate can cause malfunction of (3) Do not operate in a location subject to pneumatic equipment.
Do not use with fluids other than compressed air. Cleaning equipment is designed exclusively for use with compressed air. Contact SMC in advance if a fluid other than compressed air is to be used. 2. Do not use compressed air which contains chemicals, organic solvents or corrosive gases.
Model (Standard) Dimensions Pressure range (1) Connection thread Indication unit Model G15 MPa MPa R 1/8, M5 (Female thread) 0 to 1.0 0 to 1.0 G15-10-01 (2) 1 16 G27-10-R1 R MPa Note 1) Do not apply more excessive pressure than max. pressure display. It will be a cause of malfunction.
Do not direct the tip of the nozzle at the face or other parts of a human body. It may cause danger to personnel. 4. Do not use the product to clean or remove toxic substances or chemicals. 5. Do not drop, step on or hit the product. It may cause damage to the product. 6. Do not use the product to disturb public order or public hygiene. 7. This product is not a toy.
Do not allow pallets to strike the lever when it is standing up. Do not allow pallets to strike the lever when it is standing up (after the shock absorber has absorbed energy), because the cylinder body will be subjected to the full energy of the impact. 2. Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc.
Do not increase the operating speed after setting the operating conditions.
Do not deform the mounting surface by mounting with workpieces tucked in. 11. Do not drive the main body with the table fixed. 12. When mounting the product, for R/L type fixed cable, keep the following dimension or more for bends in the cable. For D type, keep a 40 mm or longer diameter for bends in the cable. 2.
Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 2. When problems are caused by a water hammer, install water hammer relief equipment (accumulator etc.), or use an SMC water hammer relief valve (Series VXR). Please consult with SMC for details. 5.
Do not use it in such a way that excessive external force or impact force could work on it. This could result in damage. Caution 1. Do not scratch or dent the mounting side of the body, table or end plate. The damage will result in a decrease in parallelism, vibration of the guide or an increase in moving part resistance. 2.
(If you do not the power to OFF, it does not reflect the data in the driver.) Note2) Selected Items Write: It writes the parameter values of the corresponding frame to the driver. Single Axis Write: It writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
(If you do not the power to OFF, it does not reflect the data in the driver.) Note2) Selected Items Write: It writes the parameter values of the corresponding frame to the driver. Single Axis Write: It writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.