EX260-SMJ_eng Bit: 7 0 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Bit No. 6 4 6 4 2 0 0 0 Solenoid on side A 0 2 4 6 8 16 28 30 Output No.
Do not connect multiple NFC readers / writers to a PC. Connection details using the I/O Configurator for NFC and wireless unit To use a wireless system, it is necessary to "pair" a Wireless Base and Remote. Configure this using the I/O Configurator (NFC version).
Tightening Torque for Stroke Adjustment Unit Holding Bolts Unit: Nm Bore size (mm) 25 32 40 Tightening torque End lock 1.8 3.5 Operating direction 5.8 L R Caution R L R L R L R L Do not operate with the stroke adjustment unit fixed in an intermediate position.
Do not move the cover upward inadvertently during end plate installation.
Do not block the bleed hole. If the bleed hole is blocked, the product will not operate properly. VBA VBAT AP100 875
Please do not apply force to the coil and frame when installing the piping and valves. If they receive 10 N or more of force, a malfunction may occur. 3. Do not pull the lead wire with excessive force. Applying 10 N or more of load may result in broken wire or contact failure. Manual Override Caution 1.
Do you have a process requiring cost-efficient automation? Do you have a new series of safety features to implement? In fact, do you need another pair of hands in order to solve that troublesome domestic project?
Tidy Un-friendly What do you think to the manual presentation? ! ! ! Yes Not too bad Unusable Are the explanations understandable? Which explanation was most difcult to understand: . . ! ! Are there any diagrams which are not clear? Yes No If so,which:. ! ! ! What do you think to the manual layout?
Do not drop nor apply excessive force. It may cause malfunction or damage. 3. Tighten switch by applying the wrench on the fitting part. Turning it by applying a wrench on the main body may cause damage to the product. 4. Mounting is possible in either horizontal or vertical orientation.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Operate within the range of the maximum operating pressure. VC VDW Caution VQ 1. After a long period of non-use, perform inspections before beginning operation. 2.
Do not use in lines where a pressurized condition is maintained, as the body may be damaged. Warning Caution 1. Tubing attachment/detachment for One-touch fittings 1) Installing the tubing (1) Use tubing with no flaws on its periphery and cut it off at a right angle. When cutting the tubing, use a tube cutter, TK-1, 2 or 3. Do not use pinchers, nippers or scissors, etc.
Do nol loosen the recessed head screw on the top of the sensitivity adiusting screw because ii is lor prelenting the screw trom slipping otf. @ World Wide QS\E Support... North American Branch Offices For a branch office near you call: 1-800-SMC-SMC1 (762-7621) SMC Pneumatics lnc. (Milwaukee) SMC Pneumatics lnc. (Richmond) SMC Pneumatics Inc.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not weld an arm to the cylinder. 4) Make sure to use a speed controller and adjust it to more than 1sec. when changing from clamping to unclamping (or vice versa).
Do not bring objects that are sensitive to magnetism near the cylinder. The magnet is built into the cylinder. Do not bring magnetic disks, cards or tapes near the cylinder. Data may be lost. 5. If the cylinder is operated vertically with heavy loads, measures must be taken to prevent rapid extension of the piston rod when starting to operate in the downward direction.
Free mounting Speed controllers do not protrude from the top of the body. Top mounting Bottom mounting Side mounting Wiring and piping direction can be selected depending on mounting conditions.
(Do not use any tools.) The initial exhaust rate is adjusted by turning the adjustment nut counterclockwise. x Opening of the initial exhaust valve (valve S) When the pilot pressure is applied to the pilot port S, the valve S is removed from the valve S seal assembly, and the valve opens the adjusted amount.
When using the male thread mounting type product, do not loosen the bottom nut shown in the figure below. (The bottom nut is intended to secure the connection between the bracket for the adapter connection and the male thread.) PD3 Circuit without release valve (Usage example of vacuum connection) V V PD2 PD2 Supply valve EXH. P Pressure sensor Do not loosen this nut.
Do not use it for mounting. Otherwise, the adjustment at shipment may deviate. 792