Serial Network Serial Data Transfer Multiple pieces of information transmitted one piece at a time Signal An electro-magnetic transmission that indicates or represents an occurrence. Tee A product that creates a single branch or drop from a bus. Trunk line The main bus line.
VQ1430 20 or less 26 or less Metal seal Exhaust center 110 6.3 (0.35) VQ1431 25 or less 33 or less Rubber seal 4.5 (0.25) VQ1530 20 or less 26 or less Metal seal Pressure center 6.3 (0.35) VQ1531 25 or less 33 or less Rubber seal Note 1) Values are for cylinder port size C6.
The programmed Key(s) will give an output signal for as long as the key is depressed.
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
ZF ZP ZCU D1 D2 D3 ZR1 1-K1M18 20 AMJ 10.2 Misc.
Install an air filter. Install an air filter upstream near the valve. A filtration degree of 5m or less should be selected. 3. Install an aftercooler, air dryer or drain catch before the filter and take appropriate measures. Compressed air that contains excessive foreign material may cause malfunction of valves and other pneumatic equipment.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.
VQD 24V 12V 100V 200V 110V 220V 24V DC 12V DC 100V AC 200V AC 110V AC 220V AC AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 To remove manifold from DIN rail: 1) Loosen the clamp screw on the A side of both ends of the manifold. 2) Lift the A side of the manifold off the DIN rail and slide it in the direction of the B side.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
Install an air filter. Install an air filter upstream, near the valve. Select an air filter with a filtration degree of 5 m or finer. 2. As a countermeasure, install an aftercooler, air dryer or water separator. Compressed air containing large amounts of drainage can cause malfunction of pneumatic equipment. As a countermeasure, install an aftercooler, air dryer or water separator. 3.
3) Body size With bracket B AFM20 to 40 Port size C With bowl guard AFM20 Thread type Symbol 20 30 40 J Note 5) Float type auto drain (N.C.)
12 6 24 16 8 30 20 10 lead [mm] Impact/Vibration resistance [m/s2] note4) 50 / 20 Ball screw (LEFS), Ball screw + Belt (LEFSR Actuation type L) Guide type Linear Guide Static allowable moment [Nm] Note5) 10 27 46 110 Mep (Pitching) 110 10 27 46 Mey (Yawing) 207 20 52 101 Mer (Rolling) Operating temperature range [] 5 to 40 Operating humidity range [%RH] 90 or less(No condensation) Motor
20 15 15 2 x M6 thread depth 11 (for YA type) 2 x M6 thread depth 11 (for IA type) 35 15 18 2 x M6 thread depth 11 (for IA type) 2 x M6 thread depth 11 (for YA type) 20 20 20 20 57 40 17 17 A 19.5 0.2 0.5 25 15 45 45 60 60 Material: Cast iron Unit: mm Material: Cast iron Part no.
AC adapter 20 B With an auxiliary blow NIL Without AC Adaptor (DC-plug in attached) A AC Adaptor *3 3. Photoelectronic sensor 5.
Warning It may cause an electric shock or damage to the controller. 2. Do not perform the operation or setting of this equipment with wet hands. It may cause an electric shock. 3. Product with damage or the one lacking of any components should not be used. It may cause an electric shock, fire, or injury. 4. Use only the specified combination between the controller and electric actuator.
) (CF flange) A B K S M J H G A (mm) Model A 123 170 183 217 256 B 48 66 79 100 117 C 1 2 2 3 3 D 40 55 75 87 114 Fn 95 110 Fd 70 114 Fc 26 41 52 70 83 G 41 63 68 72 98 H J K P.C.D L1 6 x 6.6 8 x 8.4 L2 XMD-25 XMD-40 XMD-50 XMD-63 XMD-80 50 65 70 88 90 16 20 20 20 20 7.5 15 17.5 19.5 26.5 P.C.D 58.7 P.C.D 92.1 C D XYD/In-line type XLA G Fd XL C XLQ (K flange) XM XY XM XY J K H B
Operating Range (mm) Bore size Switch types 25 32 20 D-A9, D-A9V D-F9, D-F9V D-F9W, D-F9WV 11 12.5 14 6.5 7 7 Values in this table include hysteresis and are to be used as a guide only. They do not guarantee an actual fixed range (expect approximately 30% dispersion).
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation.
Warning It may cause an electric shock or damage to the controller. 2. Do not perform the operation or setting of this equipment with wet hands. It may cause an electric shock. 3. Product with damage or the one lacking of any components should not be used. It may cause an electric shock, fire, or injury. 4. Use only the specified combination between the controller and electric actuator.