Mist Separator . -13- Option symbol 8 8J Semi-standard symbol Semi-standard: 8 Semi-standard: 8J Piping port Piping port (4) Part No. (4) Part No. thread ty pe thread ty pe Rc Rc C3LF-8J-A C3LF-8-A G G C3LFF-8J-A NPT C3LF-8(Z)-A NPT C3LFN-8J(Z)-A Appearance and part No.
Therefore, replace the product with a new one. (13) Pay attention to the motion of the actuator at the time of restart after the release of residual pressure. When restarting the product after releasing the residual pressure, check the initial driving direction, confirm that the work area is secured, and then restart the product.
The buttons cannot be operated. 13 Product failure Replace the product. 1. Confirm that the mounting adapter for the regulator is installed properly. Incorrect installation Correct the mounting conditions. The body has become loose. 2. Confirm that the Pressure switch is 14 installed to the mounting adapter properly. Product failure Replace the product.
Note) using a valve other then a non-polar type may cause trouble SY3000*-OMJ0003-A -13- Specific Product Precautions 7 Be sure to read before handing. One-touch Fittings M8 Connector Caution Caution 1.M8 connector types have an IP65(enclosure) rating, offering protection from dust and water. However please note: these products are not intended for use in water.
Calibrate them according to the actual application. (13) Consider mounting an elastic bumper on the pushing surface. If impact to the Card Motor cannot be avoided during pushing operation, it is recommended to mount an elastic bumper. Grounding Warning (1) Always ground the Card Motor. (2) Use a dedicated grounding. Use a D-class grounding.
Intrusion of foreign matter (11) (6),(7) Spool valve has not completely shifted. (12) Poor seal on actuator (cylinder, etc.) side (13) Insufficient bolt tightening Air leaks throuth gasket. Worn pilot valve packing Air leaks through EXH.
Doc. no.VP3145-OMM0002-B PRODUCT NAME 3 Port Solenoid Valve MODEL / Series / Product Number VP315 Series Contents Safety Instructions -2, 3 Design/Selection -4, 5 Mounting -5 Piping -5, 6 Wiring -6 Lubrication -6 Air Supply -6 Operating Environment -7 Maintenance -7 Specific Product Precautions -811 Troubleshooting -12, 13 1 No.VP3145-OMM0002-B Safety Instructions These safety instructions
Solenoid Valve PRODUCT NAME VQ7-6/VQ7-8(-X23) Series MODEL / Series / Product Number *PIN assignment of -x23 is different from standard product Contents Safety Instructions -2 5 Port Solenoid Valve Precautions -4 VQ7-6/VQ7-8 Series Specific Product Precautions -7 Series VQ7-6 Single Unit How to order/Specification -9 Construction -11 Manifold VV71 Series How to order -12 Manifold option -13
Warning Caution 13 No.VQZ100V-OMK0002-B VQZ Series/ / / /Specific Product Precautions 6 Be sure to read this before handling 2. Confirm grounding to maintain the safety or the reduced wiring system and for anti-noise performance. Grounding should be close to units and keep the grounding distance short.
Mount the switch body on the bracket properly. 13 The body is loose. Product failure Replace the product. -32No.PS-OMH0003-F Reference No. Problem Possible cause Investigation method Countermeasure Rework the piping. If excessive tightening torque over the specified range is applied, a mounting screw, mounting bracket, and switch may be broken.
Please contact SMC if it is necessary to hold a stopped position for an extended period of time. 13. Do not disassemble the product or make any modifications, including additional machining. Doing so may cause human injury and/or an accident. 14. Pilot exhaust Mount the silencer to both D and U side of the pilot exhaust port (PE) or exhaust the air to the atmosphere.
Buzzing Abrasion armature (AC coil Fall of power supply voltage 13 No.VF1000-OMN0002-A Remedy No. Remedy Regulate voltage, so that the voltage at the time of the operation becomes specifications range. Re-wire positively. Replace part. Replace part or re-wire positively. Replace valve.
. : 17 13 Option Semi-standard Semi-standard Semi-standard Part no. Part no. Port thread Port thread Rc Rc C3LF-8J-A G G C3LFF-8J-A NPT C3LF-8(Z)-A NPT C3LFN-8J(Z)-A C3LF-8-A External appearance drawing and part no. B B B HEX. : 17 1/4 Note 2 Note 2 Option Semi-standard Semi-standard Semi-standard 17 Part no. Part no.
Dimensions 13 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
(See Table 4 on page 15.) 11 - Table 3 Auto Switch Mounting Bracket / Part No. 12 - 17.5 17.5 17.5 17.5 17.5 17.5 13 - 14 - Table 4 Minimum Stroke for Auto Switch Mounting 15 - Table 5 Operating Range 16 - Auto Switch Connection and Example 17 - 3. Maintenance Caution For the CJ2-*Z series, the cover and cylinder tube are joined by rolling crimping, and cannot be disassembled.
Dimensions 13 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
However, as the metal seal closed center type valve leaks more air than the rubber seal and double check type valves, the intermediate stopping time will be shorter. 13. Do not disassemble the product or make any modifications, including additional machining. Doing so may cause human injury and/or an accident. 14.
Assemble so that the O-ring of the plate is not caught during maintenance. 12 13 Check for signs of external force having been applied to the pilot valve. External force was applied to the pilot valve. Do not apply external force to the pilot valve. 14 SMC will investigate. The following information is required for investigation, so please send it to your sales representatives.
(Refer to Section 6 Parts Replacement Procedure (pages 11 to 13) for details.) 5 XM-OMP0001-A 2. Product Specific Precautions 2 Common Specific Precautions 2 Be sure to read before handling Maintenance Parts Caution Only SMC specified parts should be used. Please refer to operation manual. The bonnet assembly should also be replaced when changing the seal material.
Grease pack part no.: GR-S-010 (10 g) 13 is a non-replaceable part, so it is not included in the seal kit. 82