Digital Gap Checker Do not use a lead wire longer than 30 m. Wire the DC (-) line (blue) as close as possible to the power supply. Operating environment Do not use the product in an environment where the product is constantly exposed to water or oil splashes. Otherwise it can cause failure or malfunction. Take measures such as using a cover.
As the connected actuator will start confirm that it is safe to do beforehand.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Open/ Close success: default output DO[101] Open / Close failure: default output DO[102] workpiece drop detection: default output DO[103] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the air gripper unit can be checked.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Do not use the product in an environment where corrosive gases or fluids can be splashed. Otherwise damage to the SI can result, causing malfunction. Do not use the product in an area where surges are generated.
Do not use until you verify that the equipment can operate properly. After mounting, repair or modification, etc., connect the air supply and electric power, and then confirm proper mounting by means of appropriate function and leak inspections. Do not let chips or extraneous material enter inside the cylinder from the inlet.
When performing neutralization, do not input the ionizer stop signal.
Piston rod Do not turn the screws at the bottom. Do not damage the sliding surface of the piston rod of the shock absorber. Otherwise, impaired durability and return failure can result. Damage is not allowed. Shock absorber is a consumable. Replace the shock absorber when the energy absorption performance is reduced.
Compressed air is mainly used to do work by acting on a piston or vane -producing some useful motion tor instance. While many tacets of industry use compressed air, the general field of Industrial Pneumatics is considered here.
Do not use in the environment, where the product could be exposed directly to the foreign matters such as powder dust, blown dust, cutting chip, spatter etc. This could result in looseness and increased operating resistance, and air leakage, etc. Please consult with SMC regarding use in this kind of environment. 3. Do not use in direct sunlight. 4.
Do not rotate the screw set on bottom of shock absorber. This is not an adjusting screw. Turning it could cause oil leakage. 2. Do not scratch the exposed portion of the piston rod. Durability could be degraded and lead to return defect.
Comfirm that the auto drain operates in the case of type with auto drain. 2.Confirm that air leakage do not occur.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not use it in this fashion. 3. An F.R.L. unit shipped from the plant has its model number labeled. However, components that are combined together during the distribution process do not have a label on them. 4.
Do not allow air flow that exceeds the rated flow. If the air flow is allowed outside the range of the rated flow even momen tarily, drainage and lubricant may splash at the outlet side or cause damage to the component. 2. Do not use in a low pressure application (such as a blower).