LA-OMT0056 Do not load the Card Motor with continuous or higher thrust than allowed for a prolonged time. When a pushing operation step data is selected, the pushing force is continuously generated from [Operation Start] until [Operation End (Stop)] is pressed.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Red flashing SI unit has detected the transmission rate, but is not addressed by the DP master OFF Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Do not connect the terminating resistor outside, when the setting switch for the terminating resistor is ON. (4)How to connect.
Although switches satisfy the IEC standard IP67 structure (JIS C0920: anti-immersion structure) (except D-A3l, A44l, G39l, K39l), do not use switches in applications where they are continually exposed to water splash or spray.
Do not exceed the screw-in torque of 3.5 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. The minimum bending radius of the cable is 50 mm. 5. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. 1. Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
Do not remove the cushion valve mechanism which prevenlS accidental removal of cushion valve. If removal of the CUShion valve mechanism is required, when thIS work is done the air supply must be turned off to prevenl election 01 the CUshion valve from the cover. i OUT 7.79 195 390 584 779 974 1130 80 25 IN 7.03 176 352 527 703 879 1019 !
Do not immerse the cylinder in water or chemicals. When the cylinder is operated in a condition with water pressure, the fluid leaks into the cylinder in the early stages. In the worst case, the fluid may back flow inside the piping and damage the solenoid valve. Maintenance Warning Mounting 1.
However, do no rotate the cushion valve exceeding two turns, and do not rotate the speed controller valve exceeding four and half turns (40: maximum two turns). If 0.6 Nm or more of torque is applied, the valve may become loose and may jump out depending on the amount of air pressure. Cushion Adjustment The air cushion is built in on the head end for the CK1 series.
Do not disassemble the power clamp No special maintenance is necessary because the power clamp has a fully enclosed design to protect the clamp against welding spatter, and also the power clamp has a contamination resistant construction. Do not disassemble any parts other than replaceable parts, otherwise it may reduce the performance of the clamp cylinder. 3.
Also, do not attempt to tighten the bumper bolt without using a nut. If the dumper bolt is removed, the piston hits the head cover causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3.
Conduit terminal: VP3185-T A B DIN terminal: VP3185-D A B [110] 81 35 Light (For TL, TZ) Max.12 31.3 G1/2 Applicable cable 6 to 12 Light position (For DL, DZ) G1/2 NO NO PE PE [243] 237.6 239 228.5 213 31 31 130 130 52 52 41 41 105 105 [ ]: With indicator light (TL, TZ) 1312 Note) CE-compliant: D/DO only (Electrical entry) VP3145/3165/3185 Series Made to Order [Option] Please contact SMC
Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases. Do not use compressed gas containing chemicals, organic solvents, salt or corrosive gas. This can cause rust, damage to rubber and resin parts, or malfunction. Liquid surface of drain Discharge drainage until the drainage level reaches the center. 3.
PAuto switch attachment Auto switches can be selected that do not protrude from cylinder body. P2 roller materials available to suit application requirements.
Do not immerse the cylinder in water or chemicals. When the cylinder is operated in a condition with water pressure, the fluid leaks into the cylinder in the early stages. In the worst case, the fluid may back flow inside the piping and damage the solenoid valve. Maintenance Warning Mounting 1.
Also, do not attempt to tighten the bumper bolt without using a nut. If the dumper bolt is removed, the piston hits the head cover causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3.
Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals, etc. will result in leakage or malfunction. 2.