High Vacuum Angle Valve, XL Series A cm Cylinder conductance With length L (cm) and diameter D (cm) where L>>D, from the formula C=(2RT/M)0.5D3/6L, the conductance C=12.1D3/L l/sec, at an air temperature of 20C. ON OFF Short pipe conductance From the Clausings factor K and the hole conductance C in the drawing below (Clausings factor drawing), the short pipe conductance CK is easily found as CK=KC.
Set of nos. above @2, @3, @4 8-29-6 7 Dual Rod Cylinder: Basic Type Series CXS Dimensions: 6 ZZ (58.5 + ST) ST SS (45 + ST) 16 8 5.5 Z (10 + 1/2 ST) 2-3.4 through 2-6.5 counterbore depth 3.3 M3 x 0.5 x 5l (Hexagon socket head set screw) 14 1 2.75 13 3 3 OUT 1 MX 5.6 3.2 MTS 0.2 28 0.2 22.7 (16) 37 35 16 28 MY 6.3 5 CY M2.5 x 0.45 x 6l 6 (Hexagon socket headcap screw) M3 x 0.5 x 12.5l, M3
When sp4l4ng two or more oplons, 6l symbols r alphabelicalorder Exampl:.BRS Nole 1) When using lhe back pressure check valve lirr lhe necessarystalions on y enterlhe back pressure clrekEl@ part no and indcale the nlmber of hanilold strlons n the spfcaton sheet Nole2) ForspecralDlN ra lenglh. ndicate DlE.terthe numberol slalons Insde ll) 1 to 10 (20) Top ported elbow Wilh 032 Onelouch lilting
Order a stainless steel screw kit (BBA1) separately, and use the M4 x 6L stainless steel set screws included in the BBA1. Note 4)There is a difference in the cylinder tube thickness depending on the cylinder model. When a band mounting type is used as an applicable auto switch and a cylinder model is changed, use caution.
Order a stainless steel screw set (BBA1) separately, and select and use the M4 x 6L stainless steel set screws included in the BBA1. 27 Cylinder with Lock Series CNA2 Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted. For detailed specifications, refer to Best Pneumatics No. 3.
actuation 350 300 250 200 150 100 50 VQD1151U 0 It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open.
Note 2) The tightening torque of the hexagon socket head cap screw (M2.5 x 6L, M2.5 x 9L) must be 0.2 to 0.3 Nm.
. -13No.PS-OMV0004-H Mounting and Installation Installation Mounting with bracket Mount the bracket to the body with mounting screws (Cross recessed round head screw: Nominal size M4 x 6L (2 pcs.)), then set the body to the specified position. : Tighten the bracket mounting screws to a torque of 0.760.1 Nm.
. -14No.PS-OMV0009-E Mounting and Installation Installation Mounting with bracket Mount the bracket to the body with mounting screws (Cross recessed round head screw: Nominal size M4 x 6L (2 pcs.)), then set the body to the specified position. : Tighten the bracket mounting screws to a torque of 0.760.1 Nm.
. -14No.PS-OMY0007-A Mounting and Installation Installation Mounting with bracket Mount the bracket to the body with mounting screws (Cross recessed round head screw: Nominal size M4 x 6L (2 pcs.)), then set the body to the specified position. : Tighten the bracket mounting screws to a torque of 0.760.1 Nm.
A cm Cylinder conductance With length L (cm) and diameter D (cm) where L>>D, from the formula C=(2RT/M)0.5D3/6L, the conductance C=12.1D3/L l/sec, at an air temperature of 20C. ON OFF Short pipe conductance From the Clausings factor K and the hole conductance C in the drawing below (Clausings factor drawing), the short pipe conductance CK is easily found as CK=KC.
Toothed lock washer (included) Phillips countersunk head screw (included) M3 x 6l Binding band (included) Holding plate (included) Refer to page 299 for mounting.
PD13 *DI6-1 Input signal device selection 6L (CN1-8) 0505h Refer to Any input signal can be assigned to the CN1-8 pin. The devices that can be assigned and the setting method are the same as in parameter No. PD03. If a value other than the initial value is set, EM1 cannot be used. the name and function field. Select the input device of the CN18 pin.
Prepare a thicker external pipe or install bypass piping. 12 Return Low Flow FLT Stop The flow rate of the circulating fluid falls short of 6L/min. The flow rate in this system falls short of your specified value. 13 Return Low Flow WRN Continued Reset the setting flow rate.
The detection position can be changed under the conditions in step 3. t t *The hexagon socket head cap screw (M2.5 x 6L) is used to fix the mounting bracket and cylinder tube. This enables the replacement of th e auto switch without adjusting its position. Confirm where the mounting position is, and tighten the auto switch fixing screw (M2.5) to fix the auto switch mounting nut.
Order a stainless steel screw set (BBA1) separately, and select and use the M4 x 6L stainless steel set screws included in the BBA1. CNA CNS CLS CLQ RLQ Besides the models listed in How to Order, the following auto switches are applicable. For detailed specifications, refer to pages 1719 to 1827.
D-G79, D-K79, D-K79C Cover Auto switch mounting screw M3 x 0.5 x 6l Auto switch Auto switch Auto switch Auto switch mounting screw M4 x 0.7 x 22l Auto switch mounting screw M3 x 0.5 x 14l Auto switch mounting band (with bracket) Cylinder tube Auto switch mounting band (with bracket) Auto switch mounting band (with bracket) 1.
MXQ 6L-mm7 Centralized adjuster / Symmetric type (6) The mounting position of the retraction stroke end adjuster is on the reverse side of functional option 6.
A cm 2 7 Ultimate Pressure Cylinder conductance With length L (cm) and diameter D (cm) where L>>D, from the formula C=(2RT/M)0.5D3/6L, the conductance C=12.1 D3/L (L/sec) at an air temperature of 20C. Ultimate pressure P (Pa) is P=Q/S, where the sum of Weight flow rates for outgassing (Qg) and leakage Q(L) is Q(Pam3/s), and the exhaust speed is S(m3/s).
CH1-12 CH2-12 Discharge Low Flow FLT Stop The flow rate of the circulating fluid falls short of 6L/min. Prepare a thicker external pipe or install bypass piping. The flow rate in the product falls short of your specified value.