When it goes OFF (when an alarm is generated), the controller output should be stopped by the sequence program. 24V, 0.2A or more 24V power supply + 10m or less 5) The LSP and LSN signals do not require wiring, because they are automatically turned ON internally at the time of shipment.
SG 12 Note 1) Do not orient diodes incorrectly. The amp will fail if connected incorrectly. Servo ON Note 2) Wiring for a standard cable less than 10m. When the cable length is 10m or longer, four lines each of P5 and LG wires should be connected in parallel.
W (44) Z (X) (V) T R (Y) T 25 IN port 2-3/8 l=280 l=300 2.5 (N) E A (U) S Q D G C C B L1 L2 L3 16 D side U side Stations 1 2 3 4 5 n 21 5.5 16 OUT port n-1/4 n-1/8 H H P=J (Pitch) 2 : Thread type L dimensions (mm) n (stations) Model Dimension 2 3 4 6 9 7 5 8 10 L1 69 103.5 138 207 310.5 241.5 172.5 276 345 VV2CW2 L2 81 115.5 150 219 322.5 253.5 184.5 288 357 L3 93 127.5 162 231 334.5 265.5
(For further information, Refer to Best Pneumatics Vol. 16.)
Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only. They can cause the coil to burn out. Caution Direction of mounting 3. Avoid sources of vibration, or adjust the arm from the body to the minimum length so that resonance will not occur.
16 Rotary Table: Basic Type Vane Style Series MSUB Size: 1, 3, 7, 20 How to Order CRB2 Connection port location CRBU2 Bearing type Nil E Side ported Axial ported B Basic type CRB1 Available with side ported only, when equipped with switch unit.
T0425 T0604 TU 0805 T0806 1/8B T1075 TU 1208 T1209 1/4B TS 1612 3/8B T1613 1/2B 3/4B 1B [Calculation example] Size: 10 Operating pressure: 0.5 MPa Inner sectional area of piping: 12.6 mm2 4.9 4 2.5 12.6 6 4 19.6 8 5 28.3 8 6 33.2 6.5 44.2 10 7.5 50.3 12 8 63.6 12 9 66.5 9.2 113 16 12 127 12.7 133 16 13 204 16.1 366 21.6 598 27.6 Lengh of piping: 1000 mm Stroke: Center Counterclockwise
Then, tighten the mounting screws to fix the valve to the manifold base. 4-7-16
Do not use any sealing agent other than seal tape. Design Warning 1. Please contact SMC when fluids other than air are used. 2. Do not supply air pressure from 2(A) port. The air will leak out from 1(P) port. 3. Since the valve allows a small volume of air leakage, it may not be suitable for holding pressure in a pressure vessel.
Do not use any other agent except a seal tape. q Contact SMC if using fluids other than air. w Do not supply air pressure from 2(A) port. The air will leak to 1(P) port. e Since the valve may have slight air leakage, it may not be suitable for holding pressure in a pressure vessel.
VHS2500 VHS3500 VHS4500 VHS5500 Model 1/8 1/4 1/4 3/8 1/4 3/8 1/2 3/4 1 1(P)/2(A) Piping port 1/2 1/4 1/8 3/8 3(R) 110 (6.11) 130 (7.22) 16 (0.89) 31 (1.72) 10 (0.56) 14 (0.78) 22 (1.22) 38 (2.11) 57 (3.17) 1(P) 2(A) Effective area (mm2) (Cv) 2(A) 3(R) Combination with a modular style FRL is possible. 33 (1.83) 40 (2.22) 14 (0.78) 29 (1.61) 11 (0.61) 16 (0.89) 15 (0.83) 29 (1.61) 51 (2.83
Do not use any sealing agent other than seal tape. Design Warning 1. Please contact SMC when fluids other than air are used. 2. Do not supply air pressure from 2(A) port. The air will leak out from 1(P) port. 3. Since the valve allows a small volume of air leakage, it may not be suitable for holding pressure in a pressure vessel.
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display.
Do not disassemble the power clamp cylinder. The power clamp cylinder consists of a completely sealed structure in order to protect it from welding spatter. Do not disassemble, except for when replacing any of the replaceable parts, as the performance may deteriorate. 10 Power Clamp Cylinder Variations Web Catalog.
When mounting the product, please do not block the exhaust port at the center of the body as this may cause performance issues.
Do not use compressed air contains chemicals, salinity, corrosive gas or synthetic oil with organic solvent. Using it may cause malfunction or damage of air gripper. Caution 1Mount air filter. Mount air filter near valve and before air gripper. Select filtration rating of 5m or less. 2Install after-cooler, air dryer and drain catch.
Do not bring objects that are sensitive to magnetism near the cylinder. The magnet is built into the cylinder. Do not bring magnetic disks, cards or tapes near the cylinder. Data may be lost. 5. If the cylinder is operated vertically with heavy loads, measures must be taken to prevent rapid extension of the piston rod when starting to operate in the downward direction.
S1 S2 Preset pressure OFF OFF P1 ON OFF P2 OFF ON P3 ON ON P4 For safety reasons, it is recommended that one of the preset pressures be set to 0MPa. 1.12-16
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 3-12-6
O F S TAT I O N S Correct 1 1 station to 6 6 stations W I R I N G DO NOT chamfer the nozzle No terminal box L Terminal Box wiring on Left Hand Side R Terminal Box wiring on Right Hand Side O P T I O N B Bracket G Gauge Incorrect D I M E N S I O N S S E E P A G E 7.16 Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 !