Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not rotate the screw more than 30 degrees for additional tightening. (The maximum tightening torque: 0.2 Nm) 3. Do not mount the product in a place where dust will be stirred up by the exhaust air from the product and affect peripheral equipment. 4. Do not mount the product in a location where air from the product will be directly exhausted to the workpiece. 5.
Apply a tightening torque of 8 to 12 Nm. When tightening, do not hold the pressure switch body with a spanner. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Apply a tightening torque of 8 to 12 Nm. When tightening, do not hold the pressure switch body with a spanner. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Note 2) Do not form connection to pins indicated with . Note 3) Signal of negative-logic circuit ON (N.C.)
Installation location Do not install this product in an area that is exposed to water or direct sunlight. Do not install in locations influenced by vibrations. If it must be used in such an area due to unavoidable circumstances, please contact SMC beforehand. 14-9-4 5 Booster Regulator Series VBA1110 to 4200 4.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove.
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. Piping Warning Air Preparation Equipment 1.
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. Piping Warning Air Preparation Equipment 1.
Do not disassemble, except for when replacing any of the replaceable parts, as this may cause the performance to deteriorate. (8) Proximity switch output The switch output signal is output near the clamping end and the unclamping end respectively.
Applicable filter model Element size (mm) Principal Parts Material ZFC100 12 x 8 x L20 I-62S-A ZFC101 Material Description Case ZFC200 16 x 12 x L25 I-63S-A Special clear nylon ZFC201 Cover PBT Note) Spare elements and O-rings for the cover are sold in sets of 10 pieces each.
During transport and installation, do not apply shock to the product, such as by dropping doing so will affect its precision. 2. Regarding the installation posture, place it perpendicular to the ground, with the zero point on the reading of a pressure gauge facing down. 3.
Identifying Version Symbols For versions lower than V2.0 and S2.0: Do not use with controller parameters higher than V2.0 or S2.0. Applicable models Applicable models JXC91m Series JXCD1m Series JXCP1m Series JXCE1m Series For versions higher than V2.0 and S2.0: Do not use with controller parameters lower than V2.0 or S2.0.
Note 1) Do not use the product in an atmosphere and place where there is direct contact with chemicals. It may cause damage to the body. (Alcohol, acetone, etc. also cause damage, so be sure for the product not to be close to them.) Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break.
The unit specification is displayed approx. 1 second Troubleshooting Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
POWER FLOW Rc (NPT)1/4 12 to 14 Nm Section A Section C Power indicator is red. Nominal size of screws Width across flats of attachment Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system. Metal piping attachment : If the error cannot be reset after the above measures are taken, then please contact SMC.
When using on the ejector etc., do not allow liquids such as water or oil to be drawn in with the air. Operating Environment 2. Do not use this product for any purposes that may adversely influence, directly or indirectly, the human body such as for food or medical applications. Warning 1.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in a place subject to heavy vibration and/or shock. 3. The valve should not be exposed to prolonged sunlight. Use a protective cover. 4. Remove any sources of excessive heat. 5.