Manifold Type: Base Mounted, Valve Stations: 6 Stations, A, B Port: NPTF1/4, CE Marked: Q (CE Marked)

Manifold Type: Base Mounted, Valve Stations: 6 Stations, A, B Port: 1/4, CE Marked: Q (CE Marked)

Manifold Type: Base Mounted, Valve Stations: 6 Stations, A, B Port: G1/4, CE Marked: Q (CE Marked)

Stations: 06, A,B Port: 1/4, Thread: NPTF

Stations: 06, A,B Port: ø3/8" One-touch Fitting, Inch, Thread: -

Stations: 06, A,B Port: 1/4, Thread: NPT

Stations: 06, A,B Port: 1/4, Thread: -

Stations: 06, A,B Port: 1/4, Thread: NPTF

Stations: 06, A,B Port: 1/4, Thread: NPT

Stations: 06, A,B Port: ø1/4" One-touch Fitting, Inch, Thread: NPTF

Stations: 06, A,B Port: ø6 One-touch Fitting, Metric, Thread: -

PF-OMM0004_C

No.PF-OMM0004-D / / PF3W7## SMC 2 11 13 14 16 17 19 21 24 26 26 F1 OUT1 60 F2 OUT2 36 F3 42 F10 43 F20 47 F22 48 F30 50 F80 51 F81 52 F82 53 F90 54 F98 55 F99 56 57 61 61 65 65 71 79 81 88 -1No.PF-OMM0004-D (ISO/IEC) (JIS) 1 2 1) ISO 4414:Pneumatic fluid power -General rules relating to systems.

Digital Flow Switch (Remote type monitor unit)

(Refer to page 42.) (Example shown is for 4 L/min type) : The set values and accumulated output of OUT2 cannot be displayed. -21No.PF-OMN0012-H Default settings When the flow exceeds the set value, the switch will be turned ON. When the flow falls below the set value by the amount of hysteresis or more, the switch will be turned OFF.

IP8101 Series

Hold down again for 1sec. or longer after interval No.DIG-31900-OM002 53 Mode button 1s Set button 1s or Mode button 1s Set button 1s or Mode button 1s Mode button 1s Set button Set button 1s 1s Fig. 42 Mode button 1s Set button 1s or Lower limiter Upper limiter Fig. 42-1 Mode button 1s Set button 1s Alarm setting Fig. 42-2 No.DIG-31900-OM002 54 Possible to select analog output

AC Servo Motor Driver (Pulse input type/Positioning type)

Positioning Mode: Minimum actuator travel distance of 1[m]. 27 - Recommended Parameter Values [LEJ] LEJS40 LEJS63 LEJB40 LEJB63 Series Lead symbol H A B H A B T Lead 24 16 8 30 20 10 27 42 Parameter *1,*2 Para. Initial value Recommended value No Number of command input pulses per revolution *3. PA05 100 100 Electronic gear numerator *3.

Air Gripper for Collaborative Robots

Air supply . 42 5-6. Piping . 43 5-7. Operating environment . 43 5-8. Lubrication . 43 6Maintenance . 43 1 - Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.

DOC1023126

Interrupting operation Item. 42 - . Procedure for power set up ..

LEC-T1_C

.**. 29 (2-3) LECPLECA .32 1 - (2-3-1) LECPA . 32 (2-3-2) LECPA . 32 (2-3-3) LECPA . 34 5.4 .36 5.4.1 .36 (1) .36 (2) .38 5.4.2 .40 (1) .40 (2) .41 6. .42 6.1 .42 (1) .42 (2) .44 (2-1) LECPLECA .44 (2-2) LECPLECA .45 (2-3) LECPA .46 6.2 .47 (1) .47 (2) .47 (3) .48 (4) .50 (5) .51 (6) .52 (7) .54 (8) .54 6.3 .56 (1) .56 (2) .56 (2-1) .56 (2-2) .56 (3) .57 (3-1) .57 (3-1-a) TB Ver1.**. 57 (

LECA6_C

CN5I/O . 23 6.1 . 23 6.2 (NPNPNP ) . 23 (1) I/O (NPNPNP ) . 23 (2) I/O . 23 6.3 . 24 6.4 I/O . 27 7. . 28 7.1 . 28 7.2 . 31 7.3 . 33 8. . 34 8.1 . 34 8.2 . 34 8.3 . 35 (1) . 35 (2) (). 35 (3) . 35 8.4 . 36 8.5 . 36 9. (). 37 9.1 . 37 9.2 . 38 10. . 39 10.1 . 39 10.2 I/O . 39 (1) . 39 (2) . 40 (3) . 41 (4) HOLD. 42 (5) . 42 2 - 6 . 42 (7) . 43 11. . 44 11.1 . 44 11.2 (). 45 11.3 I/O . 46 11.4

LECP6_C

CN5I/O .23 6.1 /.23 6.2 /(NPNPNP ).23 (1) I/O (NPNPNP ).23 (2) I/O .23 63 /.24 64 I/O .27 7 .28 71 .28 72 .31 73 .33 8 .34 81 .34 82 .34 83 .35 1 .35 2 (.35 3 .35 84 .36 85 .36 9 .37 91 .37 92 .38 10 .39 101 .39 102 I/O .39 1 .39 2 .40 3 .41 4 HOLD.42 5 .42 2 - 6 .42 7 .43 11 .44 111 [5m ].44 112 [820m].44 113 [5m ].45 114 [820m] .45 115 I/O .46 116 .46 117 .47 12. .48 12.1 .48 12.2 .49 13