Mechanically jointed rodless cylinder Basic short type (Rubber bumper), Basic standard type (Air cushion) Slide bearing guide type (Air cushion) Therefore, a method of connection which can absorb the displacement (i.e. floating mechanism) should be considered. A cylinder (Basic series MY3A/MY3B) that is suitable to be used as a driving source and a floating joint as an option are available. Please refer to the catalog for details.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
Hs B A W 16, 20, 25 Approx. Hs W A A B CUJ CU 32 to 100 Approx.
J MVGQM (Slide bearing) A, DB, E Dimensions MVGQL (Ball bushing bearing) A, DB, E Dimensions DSymbol A E Symbol Bore size (mm) 40 A DB E DB Bore size (mm) Stroke Up to 50 st Over 50 st Up to 50 st Over 50 st -X 40 54 90 0 36 16 71.5 20 17.5 50 50 60 102 4 46 20 81 25 25 2063 63 61 102 0 41 20 81 25 20 Data 10-16-13 14 Valve Mounted Guide Cylinder Series MVGQ 80, 100 How to Order How to Order
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
HOUR METER 19 Records the accumulated time an Output or Input signal has been ON SCHMITT TRIGGER 19 Turn an Input On at the High Value and Off at the Low Value (or vice versa) ZONE COMPARE 20 Compare a value to a range of values (Analog, Direct Set, or FB values) DISPLAY * Display Messages or Data on the LCD display OFFSET GAIN 22 Manipulate Analog Values; y = A/B*x + C; Set High and Low
stations 20 Port size {4(A), 2(B) port} Note 1)Order DIN rail separately.
Lube ALD600-l06 to 10, ALD900-l12 to 20 At the terminal of an air pressure line in which a D.P. Lube is used, install a strainer (filtration rate of 5m) upstream with a metal seal solenoid valve, which is susceptible to dust.
Load is an analog input equipment such as a voltmeter.
Check the voltage using a tester for more than 5 minute after power-off in case of installation, wiring and maintenance. There is a possibility of getting electric shock, fire and injury. 51 - 9. Do not use in an area where dust, powder dust, water or oil is in the air. It will cause failure or malfunction. 10. Do not use in an area where a magnetic field is generated.
characteristics 1 4/2 (P A/B) 4/2 5/3 (A/B R) Port size Manifold C [dm 3/(sbar)] b Cv C [dm 3/(sbar)] b Cv 1(P), 5/3(R) port 2(B), 4(A) port VV5Z5-20-01 VV5Z5-20-C6 VV5Z5-20-C8 VV5Z5-21-01 VV5Z5-21-C6 VV5Z5-21-C8 1/8 C6 C8 1/8 C6 C8 0.55 0.49 0.51 0.54 0.50 0.50 0.26 0.25 0.25 0.26 0.24 0.20 2.3 2.0 2.1 2.3 2.1 2.1 0.57 0.37 0.45 0.55 0.36 0.50 0.35 0.32 0.38 0.36 0.32 0.37 2.2 1.4 1.7
d nin lo inches divide by 25 4 (5.4mm = 1 in) Selection Rsference Theoretical power generation and the pressure load facior of a cylinder from a rest condition to an energized condition is demonstrated lrom the pressure load factor table and the preceding equations ln selecting an applicable rylinder, a load factor of 0.7 or less should be specified in consideration ot lowsr operating pressures
-A ZS-20-5A55 Note) When ordering a switch with 5 m lead wires, enter the part numbers for both a switch without connector and lead wires with connector.
Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -15No.PS-OMY0007-A Piping After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 15 to 20 Nm.
(mm) Table 3 Corrected value of moment center position distance (Refer to Figure 2.) 50 100 200 300 500 700 Average speed Va mm/s A, A Stroke (mm) A A A A 20 14.5 16.5 21 27 29.5 35.5 Model 150 56.5 64 125 42.5 55 64 100 34 42.5 53.5 50 75 28.5 34 33 37.5 43 50 18.5 28 25 30 33.5 43 40 18.5 20.5 25 27 29.5 35.5 30 14.5 18.5 21 27 29.5 35.5 10 14.5 16.5 21 27 29.5 35.5 Allowable moment
d nin lo inches divide by 25 4 (5.4mm = 1 in) Selection Rsference Theoretical power generation and the pressure load facior of a cylinder from a rest condition to an energized condition is demonstrated lrom the pressure load factor table and the preceding equations ln selecting an applicable rylinder, a load factor of 0.7 or less should be specified in consideration ot lowsr operating pressures
model which will provide a gripping force 10 to 20 times the weight of the workpiece.
supply port and port 1 (P) is an exhaust port. 1. 3 (R) 2 (A) Reduced pressure supply 2.
A fire or explosion can result. Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system. If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.