LEJ-OM002xx The use of screws that are too long can touch the body and cause malfunction. 11. Do not operate by fixing the table and moving the actuator body. 12. The belt drive actuator cannot be used for vertically mounted applications. 13. Vibration may occur during operation, this could be caused by the operating conditions.
And Adjust the offset voltage after supplying power. 23 Doc.No.IZ-OMK0015D (11) Timing chart Timing chart of normal operation Normal operation Reset operation Remarks Turn the power off to solve the problem, then supply power again. The error signal(OUT3) will be reset.
CONTENTS SAFETY 2 General General 3 positions 5 positions Model Indication Method 5 Names and Functions of Individual Parts 6 Installation 9 3 positions Names and Functions of Controller 11 Example of Internal Circuit and Wiring 12 Setting 15 Operation Characteristics 20 Specifications 21 5 positions Names and Functions of Controller 23 Example of Internal Circuit and Wiring 24 Setting 27
Order for tightening mounting screws 11 2-9-2. Auto switches When an auto switch is mounted or its set position is changed, refer to Fig. 4 to 11. C a u t i o n Use a specific mounting bracket (Page 19, Table 2) . Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDA).
13 90 3.2 AR60K-B 70 66 65.8 11 13 90 3.2 Note 1) B dimension is a size in the state to unlock the handle.
AW20-B 11 AW20-B 0.80.1Nm AW30-B 17 AW30-B 2.350.3Nm AW40-B 21 AW40-B 3.50.3Nm Disassembly Remove the bowl assembly, housing, and element. Hexagon Remove a housing from a body by turning 4 mounting screws to the left with a hexagon wrench key. wrench key Nominal5 Remove the valve guide.
Operation and Mounting 2.1 Air Supply -P. 5 2.2 Operating Environment -P. 6 2.3 Design -P. 6 2.4 Mounting and Installation -P. 8 2.5 Piping -P. 10 2.6 Speed Control -P. 11 2.7 Shock Absorbing Mechanism -P. 11 2.8 Directional Control -P. 12 2.9 Mounting of Auto Switch -P. 13 3. Maintenance and Inspection 3.1 Inspection -P. 14 3.2 Maintenance -P. 14 3.3 Replacement Parts -P. 14 4.
Refer to Disassembly Drawing on page 11 for the part No. and the replacement procedure of the finger assembly and the body assembly. 15 - Construction/Parts list 2 MHF2-12D to 20D Components No. Description Material Note No.
Wiring 1) Insert cable gland (4), washer (5) and rubber seal (6) into cable (7) in order, and insert it into housing (2). 2) Loosen screws (11) on terminal (3). Insert lead wires (10) and tighten screws (11) again. Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm.
Check if the dispersion is within the display accuracy range. 11 Product failure Replace the product. -52No.PS-OML0003-J Fault No. Fault Possible cause Investigation method Countermeasure Install a 5 m filter to prevent foreign matter from entering the pressure port. Also, clean the filter regularly to prevent drainage deposits.
Not adhering to these specifications, can result in damage to the product. 11 XL*-OMI0013-B 7-2.
Warranty period and guaranteed range 10 6.Parts replacement procedure 11 1 XM-OMP0001-A Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
SeriesNCQ8 Air Cylinder: Standard Type Double Acting, Single Rod Maintenance Parts 056 to 400 Construction Double Acting, Single Rod 10 11 9 Seal Kit Parts List No. 9 10 11 Description Piston Seal Rod Seal Tube Gasket Material NBR NBR NBR *BLUE links will lead to purchase pages. Repair Parts: Standard Seal Kit for Double Acting, Single Rod Remarks Bore size Kit no.
9 P3313128 P3313228 MHR3-10 MHR3-15 Description Cover Main parts MA D533 MHR3/MDHR3 Series Nominal Size 10 Without auto switch: MHR3-10R 3 x M3 x 0.5 thread depth 6 P.C.D.24 (Mounting thread) 120 120 25 25 M3 x 0.5 Finger opening port M3 x 0.5 Finger closing port 44 29 9h9 0 0.036 33.5 1 5 4 16 (36.5) 12 2 2 3e8 0.014 0.028 Open: 11 Closed: 8 8 0 0.05 4 3 x M3 x 0.5 thread depth 6 (Thread
Description Material Note No. 1 2 3 4 5 6 7 8 9 Description Material Note 20, 25: Resin Body Aluminum alloy Hard anodized MHY 10 Cap 32 to 50: Aluminum alloy Piston Hard anodized Aluminum alloy Hard anodized 11 12 13 14 15 16 17 Piston bolt Stainless steel Pinion gear Carbon steel Heat treated MHW MHW Ball bearing Carbon steel Seal cover Schield type Brass Key Carbon steel Bumper Urethane
Applicable cylinder ML2B25 ML2B32 ML2B40 MY-S25A 35 50 8 5 9.5 5.5 M6 x 1 B MY-S32A 45 64 11.7 6 11 6.6 M8 x 1.25 B Guide for Side Support Application For long stroke operation, the cylinder tube may be deflected depending on its own weight and the load. In such a case, use a side support in the middle section.
SL5201 0.5 to 10 psig (0.0034 to 0.07 MPa) SL5202 0.5 to 30 psig (0.0034 to 0.2 MPa) SL5206 1 to 60 psig (0.007 to 0.4 MPa) SL5210 1 to 100 psig (0.007 to 0.7 MPa) 100 mm Hg absolute to 10 psig (-88kPa to 0.07 MPa) Select compatible materials of construction for the gas Vacuum to 150 psig (1.0 MPa) 500 psig (3.4 MPa) 1000 psig (6.9 MPa) 40 to 160C (40 to 71C) (No freezing) 1) 0.07 2 x 10-11
NTJ-015A NT-02 NT-04 NT-05 12 M5 X 0.8 4 8 9.2 7.8 H B 20 M8 X 1.25 5 13 15.0 12.5 32, 40 M14 X 1.5 8 22 25.4 21.0 50, 63 M18 X 1.5 11 27 31.2 26 Electrical Wiring Output style Input/Output The output signal of the stroke reading cylinder is A/B phase difference output (open collector output) as shown in the figure below.
Connecting port position Rotation angle 90 180 90 180 Front port Nil Side port E Applicable auto switches/ Refer to pages 7 through 11 for detailed auto switch specifications. Lead wire length (m) Auto switch part no.