EX250-SCA1A_eng Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) SW1 SW2 SW3 SW4 SW5 SW6 Node ID Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Socket connector pin layout 5 Green / Yellow: Not connected Specifications Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
ON BUS OUT side: Link, No Activity 1 2 3 4 5 6 7 8 (Green) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Pin Allocation 4 Over current protection Yes 1 UT1 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. SF and BF Indicators Yes Over current detection 2 DI (Input signal "n+4") FS LED 3 1 BF SF Description 3 0V (US1) Fieldbus Do not operate the product outside of the specifications.
Note 3) The accessory must do the installation work by the customer oneself. HAA Series 4 1. Specifications ATX-OM-F004E Air-Cooled Aftercooler 2. Model No. Identification Mark 2Model No.
When mounting the load with screws, do not exceed the maximum tightening torque. (The torque may vary depending on the material of the load.) Bolt Model Maximum tightening torque (Nm) Caution MGJ6 M2.5 x 0.45 0.5 MGJ10 M3 x 0.5 1.0 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals can cause air leakage or malfunction, etc. 2.
Do not use valves in such environments where corrosive gases, chemicals, or brine or water or steam is airborne, or where valves can be directly exposed to any of those. 2. Do not use in an explosive environment. 3. Do not use in locations influenced by vibrations or impacts. 4. A protective cover, etc., should be used to shield valves from direct sunlight. 5.
For AC specifications, NIL is only set for Electrical entry DO. IN IN Note) Bracket cannot be attached later.
Do not load the Card Motor with continuous or higher thrust than allowed for a prolonged time. When a pushing operation step data is selected, the pushing force is continuously generated from [Operation Start] until [Operation End (Stop)] is pressed.
Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr 3. Do not service or attempt to remove pr 3.
Number of pages has been increased from 12 to 16. WQ Edition B Safety Instructions Be sure to read the Handling Precautions for SMC Products (M-E03-3) and Operation Manual before use.
Do not allow hands or fingers near the cylinder during its operation. Your fingers may be caught between the body and the plate. If you need to come near the cylinder during its operation, install a cover on the cylinder. 4. Do not bring objects that are sensitive to magnetism near the cylinder. There is a magnetic built into the cylinder.
Item CH2 measured value: 16-bit signed integer Bit offset 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 Item CH32 measured value: 16-bit signed integer Bit offset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Item CH4 measured value: 16-bit signed integer Bit offset 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Error diagnosis CH4 diagnosis CH3 diagnosis CH2 diagnosis CH1 diagnosis Reservation
(mm) Operating pressure range (MPa) Actuation speed (mm/s) MQML Standard type 6(Standard only) 10 16 20 25 6: 0.02 to 0.7 10 to 25: 0.005 to 0.7 0.5 to 1000 5 to 3000 MQMLH High speed/frequency 0.01 to 0.7 NEW NEW Low Friction Cylinder (Single Acting) Series MQP Bore size (mm) 4 6 10 16 20 Operating pressure range (MPa) Thrust control standard (N) Series 0.01 to 8 0.03 to 19 0.08 to 50 0.20
B 35 40.5 QA 6 8 QB 13 16 QV 33 38.5 A 47 58 Bore size (mm) 40 50 21 Adjustable Mounting Height Type Series RSG Rod End Configuration Lever Type with Integrated Shock Absorber Variable energy absorbing type/Flange mounting These drawings (2 items) show the piston rod extended.
-150 JC63-16-200 8 10 10 12 12 12 16 16 1 1.5 1 1.25 1.5 1.75 1.5 2 D-X Technical Data 1139 JC Series Dimensions of Accessories Rod end nut (mm) d: Thread nominal size Model Order number M8 x 1 M8 x 1.25 M10 x 1 M10 x 1.25 M10 x 1.5 M12 x 1.25 M12 x 1.5 M12 x 1.75 M14 x 1.5 M16 x 1.5 M16 x 2 M18 x 1.5 H 5 5 6 6 6 7 7 7 8 10 10 11 B C 15 15 19.6 19.6 19.6 21.9 21.9 21.9 25.4 27.7 27.7 31.2
When washing the micromesh element, do not wipe it using a stiff brush or rag. 0.03 12 08 20 24 10 16 Pressure drop (MPa) 06 0.01 0.005 COM. N.O.
Consequently, (7) the exhaust valve of (1) the pilot valve moves to the right, the output pressure of OUT1 increases that of OUT2 decreases and (16) the rotary actuator moves.
Type 16: Cassette Base Manifold. Type 10: Tie-rod Base Manifold. Manifold Option (Common for Type 16 and 10) . Single Valve/Sub-plate Type IP67 Compliant. How to Order . Specifications. Construction. Dimensions . Series SV1000. Series SV2000. Series SV3000. Series SV4000. Made to Order Specifications . Series SZ3000 5 Port Solenoid Valve Rubber Seal, Body Ported Cassette Type Manifold.