2-Layer Soft Fluoropolymer Tubing Do not use in locations having an explosive atmosphere. 2. When vibration or impact is applied, make sure to test in the 2.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not operate in environments with corrosive gases, chemicals, sea water, fresh water or water vapor, or where there will be contact with the same. 2. In locations exposed to direct sunlight, block the sunlight. 3. Do not operate in locations where vibration or impact occurs. 4. Do not operate in a location near a heat source where radiated heat will be received. Pressure gauge 1.
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specied procedures.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not operate at pressures or temperatures, etc., beyond the range of specifications, as this can cause damage or malfunction. We do not guarantee against any damage if the product is used outside of the specification range. 2.
Do not use the auto drain valve in such environment.
Burst pressure 25 20C to 60C Nylon 12 Min. bending radius (mm)(1) Operating temperature Material Note 1) The value at temp. of 20C and with O.D. variable rate 10% max.
VAC [115 VAC] Except for M5 One-touch fitting for N3 5 32" SY3000 4 220 VAC [230 VAC] Made to Order 1 4" One-touch fitting for N7 3 position pressure center One-touch fitting for N3 5 32" Nil DC specifications of type D, Y, DO and YO is only available with 12 and 24 VDC.
Applicable series (EA)5 1 (P) 3(EB) DC specifications of type D, Y, DO and YO are only available with 12 and 24 VDC.
Example 1) When the pressure in the rear and the front of the cylinder differs: Example 2) When the air supply is cut off and releasing the inlet pressure to the atmosphere, the residual pressure release of the outlet side can be ensured for a safety purpose. 1 1 2 12 2 1 2 1 3 1 2 1 14 2 4 12 L 10 5 1 3 How to Order ARP 30 03 BE K Option / Semi-standard: Select one each for a to f.
Example 1) When the pressure in the rear and the front of the cylinder differs: Example 2) When the air supply is cut off and releasing the inlet pressure to the atmosphere, the residual pressure release of the outlet side can be ensured for a safety purpose. 1 1 2 12 2 1 2 1 3 1 2 1 14 2 4 12 L 10 5 1 3 How to Order ARP 30 03 BE K Option / Semi-standard: Select one each for a to f.
When using the male thread mounting type product, do not loosen the bottom nut shown in the figure below. (The bottom nut is intended to secure the connection between the bracket for the adapter connection and the male thread.) PD3 Circuit without release valve (Usage example of vacuum connection) V V PD2 PD2 Supply valve EXH. P Pressure sensor Do not loosen this nut.
If the tightening torque is insufficient, the mounting screws and brackets may become loose. 5) Do not affix any tape or labels to the product.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 1.
So, do not apply a large amount of oil. 1. Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. Air Supply 1. Type of fluids 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion.
If the product is to remain inactive for a long period of time, remove the fluid from the pump. 12. Do not touch the pump directly with hands. The coil 4. Repeatability can be hot depending on the ambient temperature or energizing time. Install a protective cover over the valve if it can be touched directly with hands.
Refer to pages 5-12-2 to 6 for Safety lnstructions and Solenoid Valve Precautions. Mounting Definition of Symbol Warning 1. Conditions for mechanical operation Do not move the mechanical operation beyond the operating limit position, as this could damage the mechanical valve itself and lead to equipment malfunction.
They do not guarantee an actual fixed range (expect approximately 30% dispersion).