MNB B Z + Stroke DB DX DD 90 B 4-DT A DS DH 4-DR DL DU DO DO DC DE DU DA Rotating Angle Bore size (mm) Part no.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error Name Error Display Error Type Troubleshooting Method Turn the power off and remove the output factor for the over current. Then turn the power on.
Claw 1 Claw 2 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error Name Error Display Error Type Troubleshooting Method [2] Turn the power off and remove the output factor for the over current. Then turn the power on.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. This function is to display error location and content when a problem or an error occurs. Error name Error display Error type Troubleshooting method Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Preparation before setting (1)Supply pressure to the product. (2)Place the workpiece on the detection nozzle. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
the operating conditions to calculate the product life, and do not exceed it.
Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 3. Do not use in an environment where static electricity can cause problems, otherwise system failure or malfunction may result. 1. Do not drop, bump, or apply excessive impacts (980 m/s2) while handling.
Do not drop or bump. When handling the switch, do not apply an excessive impact (1000 m/s2) by dropping or striking the switch. Even if the switch case itself does not become damaged, it could damage the internal switch and cause it to malfunction. 2. Hold the product from the body side when handling. To handle the product, hold it by its body.
Do not lift the product by holding the panel, fittings or piping. Never lay the product down for transportation. This may lead to damage to the product. A polyurethane tube is attached as a drain tube for this product. Use this tube to discharge drainage to a drain tank etc. Do not use the drain tube in an upward direction. Do not bend or crush the drain tube.
Note 2) When using the D-M9lA, D-M9lAV or Y7BA, do not use the steel set screws which are included with the above auto switch mounting brackets (BA7-lll, BA4-lll).
W1 B DX Z + Stroke DDH10 hole 90 B 4-DT B DS A DH DF DU DU DL DA 4-DR DO DO DC DE Rotating Angle Bore size (mm) 40 50 63 80 100 Bore size (mm) 40 50 63 80 100 Part no.
Piping Caution Caution Handling 1.Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2.Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
The set screws in the figure below are for securing the guide shaft, so do not loosen them except for the purposes of replacing the seals. This can cause a malfunction. Caution 1. Do not use the cylinder in an environment where the cylinder is expose to moisture, adhesive foreign matter, dust or liquid such as water or cutting fluid.
A B High precision type Basic type Port location Nil E Side ported Front ported Size 1 2 3 7 A With adjustment bolt Dimensions Clean series products do not have a hollow axis.
Do not install it by directly grasping the piston rod with a pair of electricians pliers.
W1 B DX Z + Stroke DDH10 hole 90 B 4-DT B DS A DH DF DU DU DL DA 4-DR DO DO DC DE Rotating Angle Bore size (mm) 40 50 63 80 100 Bore size (mm) 40 50 63 80 100 Part no.
When installing the cylinder into equipment or performing adjustments, etc., be sure to apply air pressure of 0.25 MPa or more to the unlocking port, and do not perform work using the unlocking cam. 3.
Do not operate the CS1 series at twice the output. Applicable Series Series Description Note Vol. no.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of the auto drain will stop water vapor from discharging through the air outlet.) If it is unavoidable that the tube goes upwards, make sure it only goes as far as the position of the auto drain. Power Supply Caution Connect the power supply to the terminal block.