80 Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not apply external force to the coil. Apply a wrench to the exterior surface of the piping joint at the time of tightening. 3. Do not use heat insulators, etc. to keep the temperature at the coil assembly. Do not use a tape heater for freeze prevention except on the piping and body. If may cause the coil to burn. Caution 1.
Do not disassemble or perform any conversion work on flow switches. 4.
Do not disassemble the product. Products which have been disassembled cannot be guaranteed. If disassembly is necessary, please contact SMC. Operating Environment Warning 1. Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in explosive atmospheres. 3.
Operating Environment Maintenance Caution Warning 1.Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2.Do not use in locations subject to vibration or impact.
Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 6.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water vapor, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not apply an excessive force to the finger guard. If an excessive external force is applied to the finger guard (including the filter holder) on the air suction side of the product, it may be broken. Do not apply an external force of 50 N or more to the finger guard. Caution 1. Clean specification is not available with this product.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water or water steam is present. 2. Do not expose the product to direct sunlight for an extended period of time. 3. Do not operate in a location subject to vibration or impact. 4. Do not mount the product in locations where it is exposed to radiant heat. 5.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water or water steam is present. 2. Do not expose the product to direct sunlight for an extended period of time. 3. Do not operate in a location subject to vibration or impact. 4. Do not mount the product in locations where it is exposed to radiant heat. 5.
Do not use this product with a fluid other than compressed air (e.g. oxygen, hydrogen, inflammable gas, mixed gas, etc.). -Do not use compressed air which includes chemicals, organic solvents, or corrosive gases, etc. It may lead to damage or malfunction. Do not use for caisson shield, breathing, medical purposes, air blow to any medicines and foods that enter the human body.
Example Warning Mounting 0.1 0.2 0.3 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 2. Insert the cable through the conduit and install the wires according to the terminal board layout below. Manifold expansion 0.4 0 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not touch the span calibration trimmer except when performing span calibration. Touching the trimmer may cause generation of an error in the measured pressure. Also do not turn it too hard (0.3 Nm or less) or press it too hard (5 N or less). 7. Use a soft cloth to wipe the blot off of the body.
Do not use the valves in an atmosphere having corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Do not use in locations subject to vibration or impact. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 4.
Do not touch the span calibration trimmer except when performing span calibration. Touching the trimmer may cause generation of an error in the measured pressure. Also do not turn it too hard (0.3 Nm or less) or press it too hard (5 N or less). 7. Use a soft cloth to wipe the blot off of the body.
Do not attempt to rotate the connector, as it is not rotatable.
Do not use until you can verify that equipment can operate properly. Verify correct mounting by suitable function and leakage inspections after air and power are connected following mounting, maintenance or conversions. 2. Do not drop or bump. Do not drop, bump or apply excessive impact (1000 m/s2) when handling.
Do not scratch or gouge the sliding part of the piston rod or guide rod. This will cause air leakage or malfunction due to damage of the seals. 2.
Conditions for mechanical operation Do not move the mechanical operation beyond the operating limit position, as this could damage the mechanical valve itself and lead to equipment malfunction. Actuator stroke Operate the mechanism within the stroke range that has been obtained through the formula given below. (Do not move beyond the operating limit position.)
Do not use tools, such as pliers, to rotate the knob. This can cause the idle rotation of the knob or damage. 3. Do not overtighten the lock nut. It is possible to tighten the lock nut (hexagon) manually. When tightening further with tools, tighten by approximately 15 to 30. Overtightening may cause breakage.