S070 With the 0.1 W specification, the vibration and impact resistance is 10/50 m/s2 or less. Note 3) With the low vacuum specification, the operating pressure range is 1.33 102 Pa to the maximum operating pressure.
With the 0.1 W specification, the vibration and impact resistance is 10/50 m/s2 or less. Note 3) With the low vacuum specification, the operating pressure range is 1.33 102 Pa to the maximum operating pressure.
P1 LED lever meter Sensor S1 S3 Red is on: Output OFF Green is on: Output ON S4 S2 + P2 Red 1 Gap too big S1, S2: Fixed orifice S3: Variable orifice (Set via adjustment knob) S4: Detection nozzle Red 2 Green 1 BEST POSITION The bridge circuit is constructed as shown in the diagram. Position the work piece in front of the nozzle (S4).
Do not drop or apply the excessive force (1000 m/s2) to a switch when handling. Do not drop, or bump, or apply the excessive force (more than 1000 m/s2) when handling a switch. The internal parts of a switch are damaged, and may result in a malfunction, even though a switch case itself is not damaged. 2. When handling a switch, hold it by the switch body.
With the 0.1 W specification, the vibration and impact resistance is 10/50 m/s2 or less. Note 3) With the low vacuum specification, the operating pressure range is 1.33 102 Pa to the maximum operating pressure.
Mount the switch in a locations where there is no vibration greater than 98 m/s2 or impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
REC Smooth acceleration & deceleration at 5 CX CY MQQ M Acceleration Stroke Cushion seal RHC MK(2) 15 m/s2 5 m/s2 (REB) (REA) RS Q G High precision guide type: REAHT (Double axis) High precision guide type: REBHT (Double axis) RS H A REB REA RZQ High precision guide type: REAH (Single axis) High precision guide type: REBH (Single axis) MI W S High Linear guide (Double axis) installed in the
Do not drop, bump or apply excessive impacts (980 m/s2 or more for sensor unit and 98 m/s2 or more for amplifier unit) while handling. Although the trimmer auto switch body may not be damaged, the inside of the trimmer auto switch could be damaged and cause a malfunction. 2. Refer to the Operation Manual for how to adjust/set. Maintenance Warning 1.
(Value in the initial stage) Note 3) Vibration resistance is 50 m/s2 when a light/surge voltage suppressor is attached. Note 4) No inrush voltages are generated in the AC solenoid because a full-wave rectifier is used. VXA VCH VDW Construction VQ Component Parts !6 e !5 o y i q t u !0 !1 e w r !3 !8 !7 @3 @0 !9 @4 @1 @2 @6 @5 @7 @8 LVM No.
A Controller type Motor type Power supply voltage Symbol Type AC servo motor (S2) Capacity Encoder LECSA1-S1 LECSA1-S3 LECSA2-S1 LECSA2-S3 LECSA2-S4 LECSB1-S5 LECSB1-S7 LECSB2-S5 LECSB2-S7 LECSB2-S8 AC servo motor (S2) 100 to 120 VAC 50/60 Hz S1 S3 S4 S5 S7 S8 100 W B Pulse input type (For absolute encoder) AC servo motor (S3) Pulse input type (For incremental encoder) Incremental AC servo
After improvement Before improvement Conventional coil tube model Filter regulator Conventional coupler model S coupler 1 2 1 2 Coil tube L L VMG Air gun Nozzle 2.5 Nozzle 3 S2 S0 to S1 S2 S0 to S1 Effective area ratio 3.04 : 1 Effective area ratio 0.69 : 1 Before improvement After improvement Coupler S coupler Conventional model Piping Equipment TCU1065-1-20-X6 Conventional coil tube model
Note) Old VXZ bracket mounting hole center position 26 Zero Differential Pressure Type Pilot Operated 2 Port Solenoid Valve Series VXZ Air Air Oil Water Dimensions/Body Material: Aluminum, C37, Stainless Steel For Air Specifications For Water For Oil Options Construction Dimensions For Heated Water For High Temperature Oil Conduit Conduit terminal 34 D D G1/2 Q2 S2 F F Q 280 23 32 a e E R
m/s2) *3 100 *1: Values are based on standard of SMC measurements.
Smooth acceleration & deceleration at 5 Acceleration Stroke 15m/s2 (REB) 5m/s2 (REA) REB REA 1/2 T T Time Cushion ring The exterior of the cushion ring is provided with a variable throttle groove in its longitudinal direction.
(Between lead wire and the case) 1000 m/s2 300 m/s2 Impact resistance 50 M or more at 500 M VDC (Between lead wire and case) Insulation resistance 1500 VAC for 1 minute 1) (Between lead wire and case) 1000 VAC for 1 minute (Between lead wire and case) Withstand voltage Except magnetic resistant 2-color indication type solid state switch (DP5DWL/P5DWSC).
ripple 10% or less) Current consumption 20mA or less (without load) Enclosure IP65 Operating temperature range Operating: 0 to 50C, Stored: 25 to 85C in stock (no freeze nor condensation) Environmental resistance Voltage resistance 1000VAC for 1 min between external terminals and case Insulation resistance 50M or more (500VDC) between external terminals and case Vibration resistance 4.9m/s2
2.5% F.S. or less Note 3) No-voltage input (solid state switch or reed switch), input 5ms or more IP65 Operating: 0 to 50C, Stored: 10 to 60C (With no condensation or freezing) Operating and stored: 35 to 85% RH (With no condensation) 250VAC for 1 min, between all lead wires and enclosure 2M or more (at 50VDC) between all lead wires and enclosure 10 to 500Hz with 1.5mm amplitude or 98m/s2
This reduces noise considerably compared with A much lower air consumption is required than the current model. the current model. 1: Conditions: Unseated for 5 seconds and seated for 20 seconds (For G type) Comparison of detection circuit ISA3 New New Current model (ISA2) A B EXH port EXH port P1 Sensor Sensor SUP port S1 S3 SUP port S2 Sensor S1 S4 S2 Detection port P2 Detection port C D
Do not drop, hit or apply excessive shock (100 m/s2 or more) to the product when handling it. Even if the product appears undamaged, the internal components may be damaged, leading to a malfunction. 2. When mounting/dismounting the cable, use your finger to pinch the claw of the connector, then attach/detach it correctly.