Environment M O U N T I N G S Full range of NFPA accessories.
7 @2 @3 @4 r y e #7 u o !1 i w !8 #4 !6 A @0 @1 !9 #2 !0 #1 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com A Ball bushing bearing #5 @5 #0 @6 @8 !7 !3 #8 !2 @1 !
Special resin Carbon steel Description No. q w e r t y u i o !
C a u t i o n Piston speed should be controlled gradually from low speed with a speed controller fully closed to the specified speed. 2-6. Cushion C a u t i o n Cylinder cushions are adjusted properly before shipping, re-adjust the cushion valve on the cover according to the load and the operating speed.
T h e r e i s n o p a r t i c u l a r p r o b l e m i n u s i n g t h e s y s t e m . R e a d t h e i n s t r u c t i o n m a n u a l W i l l y o u d o a t h o r o u g h l y f o r t h i s i t e m a n d c o u n t e r p o s i t i o n i n g m o t i o n ?
C a u t i o n Piston speed should be controlled gradually from low speed with a speed controller fully closed to the specified speed. 2-6. Cushion C a u t i o n Cylinder cushions are adjusted properly before shipping, re-adjust the cushion valve on the cover according to the load and the operating speed.
C a u t i o n Piston speed should be controlled gradually from low speed with a speed controller fully closed to the specified speed. 2-6. Cushion C a u t i o n Cylinder cushions are adjusted properly before shipping, re-adjust the cushion valve on the cover according to the load and the operating speed.
of poppet valves u close due to the balance between actuating forces F1 and F2.
For type R, U, DC voltage is only available. Power saving circuit is only available in the "Z" type.
U U U O O O O S S S S H H H H L L L L to to to to Possible to change to the optional mounting angles.
: 2 to 10 stations U side: 2 to 10 stations Nil Standard length (Specify a longer rail than the standard length.)
The U-phase and V-phase currents must be adjusted so that they balance. Repeat the adjustment alternately between them several times. Repeat the operations of steps 4 to 6 (phase-U and-V alternately) until adjusting the offset amounts both for phase-U and -V in both directions cannot reduce the torque ripple any more. Then, perform the same operation by adjusting by smaller amount.
HNBR POM, Stainless steel Note) u u Seal Cassette NBR POM, Stainless steel (1) i i O-ring Seal NBR NBR o o O-ring O-ring NBR NBR !
U Approx. U A B B A D-A7H D-A80H D-F7 D-J79 D-F7W D-J79W D-F7F D-F7NTL D-F7BAL SMC SMC Approx. U SMC SMC Approx. U B A B A Approx. U D-A73C D-A80C D-J79C D-A7*C,D-A80C Approx. U Approx. U D-A7*C,D-A80C A B A B Approx.
U B A Approx. U A B D-A7H D-A80H D-F7 D-J79 D-F7W D-J79W D-F7F D-F7NTL D-F7BAL SMC SMC Approx. U Approx. U Approx. U SMC SMC Approx. U A B B A Approx. U D-A73C D-A80C D-J79C B A A B Approx.
M M type plug connector U With light/surge voltage suppressor (Non-polar type) * S type: Not available for AC * U type: DC only o Body surface treatment/Seal material and changed parts Body surface treatment Part with changed seal material and leakage Symbol Changed part *2 Leakage [Pam3/s or less] *1 Symbol Surface treatment Nil External: Hard anodized Internal: Raw material A External
10 180 S Standard Size 10 15 20 30 40 Size 10 15 90 CDRBU2 W U 10 180 S With auto switch Sizes: 10, 15 With auto switch Sizes: 20, 30, 40 CDRBU2 W U 20 180 S R73 Number of auto switches 1 pc.
35 26 36.5 30 40.5 29 39.5 40 CC 27 39 31 43 31.5 43.5 28.5 40.5 30 42 34 46 33 45 50 29.5 40 33.5 44 34 44.5 31 41.5 32.5 43 36.5 47 35.5 46 RB 63 33 43 37 47 37.5 47.5 34.5 44.5 36 46 40 50 39 49 J D-A7H,A80H D-F7,D-F79F D-J79,J79W D-F7W D-F7BAL D-F7NTL DD-F7V D-F7WV D-F7BAVL D-A9V D-J79C D-A79W D-P5DWL D-F9BAL D-A73C D-A80C D-M9V D-F9WV D-A7,A80 Bore size (mm) -X 20U U U U U U U U U U
During Auto tuning Auto tuning failure A T 1 E R R 1 9 P V < 2 3 . 0 C # 1 A T F a i l u r e A u t o T u n i n g M O D E S h u t O f f C a n c e l : A T k e y <4> External sensor sampling cycle setting: Mode indication External Sensor Sampling Cycle. Default value: 180 sec. Setting range 10 to 999 sec.