Mechanically Jointed Rodless Cylinder Series MY2 ø16, ø25, ø40 1

X417 on both sides (one on each side) X417 on L unit side X417 on H unit side L, H LH LH LH LH L, H, LS, HS L, H LH LH X416 X417 Note) For LS and HS, the stroke adjusting unit is mounted on one side only. 8-13-32 5 Holder Mounting Bracket q, w -X416/X417 Example Example Stroke adjusting unit with holder mounting bracket MY2H-A25L-X416 (L unit for MY2H25 and X416 bracket) L units with one

Mechanically Jointed Rodless Cylinder With Protective Cover Series MY1  W ø16, ø20, ø25, ø32, ø40, ø50, ø63 1

(Except 50) MY1MW16/20/50/63 MY1CW16/20/50/63 L L L L L L R R R R R R R L L R R R L L L R Slide table operating direction MY1MW25/32/40 MY1CW25/32/40 L L This port is not available for use. (Except 32, 40) L L L L L L L L R R R R R R R R L L R R L L L R Slide table operating direction 8-12-3 4 Series MY1W Specific Product Precautions 2 Be sure to read before handling.

Mechanically Jointed Rodless Cylinder With Protective Cover Series MY1  W ø16, ø20, ø25, ø32, ø40, ø50, ø63 1

(Except 50) MY1MW16/20/50/63 MY1CW16/20/50/63 L L L L L L R R R R R R R L L R R R L L L R Slide table operating direction MY1MW25/32/40 MY1CW25/32/40 L L This port is not available for use. (Except 32, 40) L L L L L L L L R R R R R R R R L L R R L L L R Slide table operating direction 8-12-3 4 Series MY1W Specific Product Precautions 2 Be sure to read before handling.

MY1

(Except 32, 40) Side port Side port Back port Back port L L L Front port Front port L L L L L R R R R R R O-ring R R L L R R Bottom port Bottom port DL L Piping tube -X L R Technical Data Slide table operating direction For bottom piping, refer to the figure above. 1365

Mechanically Jointed Rodless Cylinder MY1H Series Linear Guide Type: ø25, ø32, ø40  Piping can be connected from 4 directions on the head cover.  Allows on-site piping to suit the MY1B installation MY1H MY1H conditions. MY1B MY1M MY1C MY

Standard piping type Centralized piping type Operating direction Operating direction Side Front Side Front L R L R L L L R L R R R R R R R L L L L L R L L L Back New Back R R R Bottom Bottom Port variation Port variation R and L can be mounted in any desired position.

Mechanically Jointed Rodless Cylinder Series MY2

Applicable cylinder Port variation MY2C16/25/40 MY2H16/25/40 MY2HT16/25/40 R R L L L L L L L L R R R R R R L R Slide table operating direction 1118

Mechanically Jointed Rodless Cylinder Series MY2H/HT ø16, ø25, ø40

L F9NWL 5m...

AC Servo Motor Driver ( ＳＳＣＮＥＴⅢ/H Type ）

Regenerative option PA02 0 0(Non) / 0002(LEC-MR-RB-032) Rotation direction selection PA14 0 1(+Counter motors side) Load to motor inertia moment ratio PB06 7 7 Function selection E-3 PE41 0 0 LEFS25(L,R)T6 LEFS32(L,R)T7 LEFS40(L,R)T8 /LEKFS25(L,R)T6 /LEKFS32(L,R)T7 /LEKFS40(L,R)T8 Series Lead symbol H A B H A B H A B Lead 20 12 6 24 16 8 30 20 10 Parameter *1,*2 Para.

CNG

m l m m m L L t t t t B1 H1 Dd9 Applicable bore size (mm) L L Dd9 d l l d m t Applicable bore size (mm) Part no.

CNG

m l m m m L L t t t t B1 H1 (mm) (mm) (mm) Dd9 Applicable bore size (mm) L L Dd9 d l l d m t Snap ring Snap ring t m Part No.

CNG

m l m m m L L t t t t B1 H1 Dd9 Applicable bore size (mm) L L Dd9 d l l d m t Applicable bore size (mm) Part no.

Cylinder with Lock Series CNG

m l m m m L L t t t t B1 H1 (mm) (mm) (mm) Dd9 Applicable bore size (mm) L L Dd9 d l l d m t Snap ring Snap ring t m Part No.

Compact Rotary Actuator Series CRQ2

l Center of rotation and center of gravity of the load are concentric. Gravity is applied. mg F l l mg Friction force is applied. Rotation shaft is vertical (up and down). 2 Ta = = t2 Ts = F l Gravity is applied in rotating direction.

CG5-S

m L (mm) Part no.

CG5-S

m L (mm) Part no.

CJ5-S

m L Part no.

CJ5-S

m L Part no.

e

L-bracket DIN rail bracket MYE-DB 1133 Series E-MY2H/HT Dimensions: Integrated Control Type E-MY2H Nominal size Stroke Nominal size: 16 A clearance of 40 mm or greater is required.

Possible to transfer a workpiece at low-speed.

L Gravity is applied. Center of rotation and center of gravity of the load are concentric. mg F L L mg Friction force is applied. Rotation shaft is vertical (up and down). 2 Ta = = t2 Ts = F L Gravity is applied in rotating direction.

2 Finger, 3 Finger, 4 Finger Air Gripper Parallel Type Series MHS

= 20mm, and for 32 to 63 with gripping point L = 30mm.